Fix enable_internal_pullup to always use pull-ups

.eil.yml

@@ -1,7 +1,7 @@
 ---
 name: encoder
 description: HW timer-based driver for incremental rotary encoders
-version: 3.0.0
+version: 3.0.1
 groups:
   - input
 code_owners:

encoder.c

@@ -224,40 +224,30 @@ esp_err_t rotary_encoder_create(const rotary_encoder_config_t *config, rotary_en
     }
 #endif
 
-    // setup GPIO
-    gpio_config_t io_conf;
-    memset(&io_conf, 0, sizeof(gpio_config_t));
-    io_conf.mode = GPIO_MODE_INPUT;
-    if (config->enable_internal_pullup)
+    // setup GPIO pins as inputs
+    gpio_num_t pins[] = { re->pin_a, re->pin_b, re->pin_btn };
+    int num_pins = PIN_VALID(re->pin_btn) ? 3 : 2;
+    esp_err_t err;
+    for (int i = 0; i < num_pins; i++)
     {
-        if (re->btn_pressed_level == 0)
+        err = gpio_set_direction(pins[i], GPIO_MODE_INPUT);
+        if (err != ESP_OK)
         {
-            io_conf.pull_up_en = GPIO_PULLUP_ENABLE;
-            io_conf.pull_down_en = GPIO_PULLDOWN_DISABLE;
+            vSemaphoreDelete(re->lock);
+            free(re);
+            return err;
         }
-        else
+        if (config->enable_internal_pullup)
         {
-            io_conf.pull_up_en = GPIO_PULLUP_DISABLE;
-            io_conf.pull_down_en = GPIO_PULLDOWN_ENABLE;
+            err = gpio_set_pull_mode(pins[i], GPIO_PULLUP_ONLY);
+            if (err != ESP_OK)
+            {
+                vSemaphoreDelete(re->lock);
+                free(re);
+                return err;
+            }
         }
     }
-    else
-    {
-        io_conf.pull_up_en = GPIO_PULLUP_DISABLE;
-        io_conf.pull_down_en = GPIO_PULLDOWN_DISABLE;
-    }
-    io_conf.intr_type = GPIO_INTR_DISABLE;
-    io_conf.pin_bit_mask = GPIO_BIT(re->pin_a) | GPIO_BIT(re->pin_b);
-    if (PIN_VALID(re->pin_btn))
-        io_conf.pin_bit_mask |= GPIO_BIT(re->pin_btn);
-
-    esp_err_t err = gpio_config(&io_conf);
-    if (err != ESP_OK)
-    {
-        vSemaphoreDelete(re->lock);
-        free(re);
-        return err;
-    }
 
     // Create and start per-encoder timer
     const esp_timer_create_args_t timer_args =

encoder.h

@@ -96,8 +96,18 @@ typedef struct
     gpio_num_t pin_a;                    //!< Encoder pin A
     gpio_num_t pin_b;                    //!< Encoder pin B
     gpio_num_t pin_btn;                  //!< Button pin, or GPIO_NUM_NC if unused
-    uint8_t btn_pressed_level;           //!< GPIO level when button is pressed (0 or 1)
-    bool enable_internal_pullup;         //!< Enable internal pull-up/pull-down resistors on GPIO pins
+    uint8_t btn_pressed_level;           //!< GPIO level when button is pressed (0 or 1).
+    //!< When set to 1, the button pin may need a pull-down
+    //!< resistor, either external or set via \c gpio_set_pull_mode()
+    //!< before creating the encoder, as \c enable_internal_pullup
+    //!< only enables pull-ups.
+    bool enable_internal_pullup;         //!< Enable internal pull-up resistors on all encoder and
+    //!< button GPIO pins. Pull-ups are always used, which is
+    //!< correct for encoders wired with common to ground. When
+    //!< \c btn_pressed_level is 1, the button pin may need a
+    //!< pull-down instead — use an external resistor or call
+    //!< \c gpio_set_pull_mode() before creating the encoder.
+    //!< When false, pull resistors are left unchanged.
     uint32_t btn_dead_time_us;           //!< Button dead time in microseconds
     uint32_t btn_long_press_time_us;     //!< Long press threshold in microseconds
     uint32_t acceleration_threshold_ms;  //!< Acceleration threshold in milliseconds (acceleration starts below this interval)

idf_component.yml

@@ -1,5 +1,5 @@
 ---
-version: 3.0.0
+version: 3.0.1
 description: HW timer-based driver for incremental rotary encoders
 license: BSD-3
 targets: