diff --git a/configs/sim/axis/sedm/Etabs/19.ENC b/configs/sim/axis/sedm/Etabs/19.ENC new file mode 100644 index 00000000000..4e18c17eb3f --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/19.ENC @@ -0,0 +1,19 @@ +19.ENC MM CU+ ST= ~020"/s UNS +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 80 0 0 40 30 440 212 0 2.0 3.0 10 0.508 0.0 0 0 0 +24 56 0 0 40 30 440 212 0 2.0 3.0 10 0.066 45.0 0 0 0 +23 56 0 0 40 30 288 140 0 2.0 3.0 10 0.119 40.0 0 0 0 +22 40 0 0 40 30 288 140 0 2.0 3.0 10 0.157 36.0 0 0 0 +21 40 0 0 40 30 172 100 0 2.0 3.0 10 0.211 32.0 0 0 0 +20 27 0 0 40 30 172 100 0 2.0 3.0 10 0.244 29.0 0 0 0 +19 27 0 0 40 30 100 60 0 2.0 3.0 10 0.284 26.0 0 0 0 +18 19 0 0 40 30 100 60 0 2.0 3.0 10 0.315 23.0 0 0 0 +17 19 0 0 40 30 60 36 0 2.0 3.0 10 0.345 20.0 0 0 0 +16 14 0 0 40 30 60 36 0 2.0 3.0 10 0.366 17.0 0 0 0 +15 14 0 0 40 30 36 24 0 2.0 3.0 10 0.391 14.0 0 0 0 +14 10 0 0 40 30 36 24 0 2.0 3.0 10 0.409 12.0 0 0 0 +13 10 0 0 40 30 20 16 0 2.0 3.0 10 0.429 10.0 0 0 0 +12 7 0 0 40 30 20 16 0 2.0 3.0 10 0.442 8.0 0 0 0 +11 7 0 0 40 30 12 12 0 2.0 3.0 10 0.455 6.0 0 0 0 +10 7 0 0 40 30 8 12 0 2.0 3.0 10 0.465 4.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/20.ENC b/configs/sim/axis/sedm/Etabs/20.ENC new file mode 100644 index 00000000000..a5bad96891d --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/20.ENC @@ -0,0 +1,17 @@ +20.ENC MM CU+ ST- ~0.025"/s UNS +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 110 0 0 40 30 440 212 0 2.0 3.0 10 0.635 0.0 0 0 0 +24 72 0 0 40 30 440 212 0 2.0 3.0 10 0.137 45.0 0 0 0 +23 72 0 0 40 30 288 140 0 2.0 3.0 10 0.196 40.0 0 0 0 +22 43 0 0 40 30 288 140 0 2.0 3.0 10 0.262 35.0 0 0 0 +21 43 0 0 40 30 172 100 0 2.0 3.0 10 0.32 30.0 0 0 0 +20 26 0 0 40 30 172 100 0 2.0 3.0 10 0.368 25.0 0 0 0 +19 26 0 0 40 30 100 60 0 2.0 3.0 10 0.411 20.0 0 0 0 +18 15 0 0 40 30 100 60 0 2.0 3.0 10 0.452 15.0 0 0 0 +17 15 0 0 40 30 60 36 0 2.0 3.0 10 0.483 12.0 0 0 0 +16 9 0 0 40 30 60 36 0 2.0 3.0 10 0.513 10.0 0 0 0 +15 9 0 0 40 30 36 24 0 2.0 3.0 10 0.538 8.0 0 0 0 +14 7 0 0 40 30 20 16 0 2.0 3.0 10 0.566 6.0 0 0 0 +13 7 0 0 40 30 12 12 0 2.0 3.0 10 0.582 4.0 0 0 0 +12 7 0 0 40 30 8 12 0 2.0 3.0 10 0.592 3.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/21.ENC b/configs/sim/axis/sedm/Etabs/21.ENC new file mode 100644 index 00000000000..2d375305a72 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/21.ENC @@ -0,0 +1,18 @@ +21.ENC MM CU+ ST- ~0.028"/sUNS +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 140 0 0 40 30 440 212 0 2.0 3.0 10 0.762 0.0 0 0 0 +24 100 0 0 40 30 440 212 0 2.0 3.0 10 0.193 45.0 0 0 0 +23 100 0 0 40 30 288 140 0 2.0 3.0 10 0.257 40.0 0 0 0 +22 55 0 0 40 30 288 140 0 2.0 3.0 10 0.353 35.0 0 0 0 +21 55 0 0 40 30 172 100 0 2.0 3.0 10 0.414 30.0 0 0 0 +20 32 0 0 40 30 172 100 0 2.0 3.0 10 0.467 25.0 0 0 0 +19 32 0 0 40 30 100 60 0 2.0 3.0 10 0.516 20.0 0 0 0 +18 20 0 0 40 30 100 60 0 2.0 3.0 10 0.556 17.0 0 0 0 +17 20 0 0 40 30 60 36 0 2.0 3.0 10 0.589 15.0 0 0 0 +16 11 0 0 40 30 60 36 0 2.0 3.0 10 0.625 12.0 0 0 0 +15 11 0 0 40 30 36 24 0 2.0 3.0 10 0.65 10.0 0 0 0 +14 7 0 0 40 30 36 24 0 2.0 3.0 10 0.673 8.0 0 0 0 +13 7 0 0 40 30 20 12 0 2.0 3.0 10 0.693 6.0 0 0 0 +12 7 0 0 40 30 12 12 0 2.0 3.0 10 0.709 4.0 0 0 0 +11 7 0 0 40 30 8 12 0 2.0 3.0 10 0.719 3.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/22.ENC b/configs/sim/axis/sedm/Etabs/22.ENC new file mode 100644 index 00000000000..d1820846e05 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/22.ENC @@ -0,0 +1,19 @@ +22.ENC MM CU+ ST - ~0.036"/s UNS +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 170 0 0 40 30 440 212 0 2.0 3.0 10 0.889 0.0 0 0 0 +24 120 0 0 40 30 440 212 0 2.0 3.0 10 0.221 45.0 0 0 0 +23 120 0 0 40 30 288 140 0 2.0 3.0 10 0.292 40.0 0 0 0 +22 84 0 0 40 30 288 140 0 2.0 3.0 10 0.411 35.0 0 0 0 +21 84 0 0 40 30 172 100 0 2.0 3.0 10 0.478 30.0 0 0 0 +20 50 0 0 40 30 172 100 0 2.0 3.0 10 0.549 25.0 0 0 0 +19 50 0 0 40 30 100 60 0 2.0 3.0 10 0.602 20.0 0 0 0 +18 30 0 0 40 30 100 60 0 2.0 3.0 10 0.645 18.0 0 0 0 +17 30 0 0 40 30 60 36 0 2.0 3.0 10 0.683 16.0 0 0 0 +16 18 0 0 40 30 60 36 0 2.0 3.0 10 0.721 14.0 0 0 0 +15 18 0 0 40 30 36 24 0 2.0 3.0 10 0.749 12.0 0 0 0 +14 10 0 0 40 30 36 24 0 2.0 3.0 10 0.782 10.0 0 0 0 +13 10 0 0 40 30 20 16 0 2.0 3.0 10 0.805 8.0 0 0 0 +12 7 0 0 40 30 20 16 0 2.0 3.0 10 0.82 6.0 0 0 0 +11 7 0 0 40 30 12 12 0 2.0 3.0 10 0.836 4.0 0 0 0 +10 7 0 0 40 30 8 12 0 2.0 3.0 10 0.846 3.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/23.ENC b/configs/sim/axis/sedm/Etabs/23.ENC new file mode 100644 index 00000000000..f390b20a085 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/23.ENC @@ -0,0 +1,19 @@ +23.ENC MM CU+ ST- ~0.040"/s UNS +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 190 0 0 40 30 440 212 0 2.0 3.0 10 1.016 0.0 0 0 0 +24 140 0 0 40 30 440 212 0 2.0 3.0 10 0.274 45.0 0 0 0 +23 140 0 0 40 30 264 128 0 2.0 3.0 10 0.356 40.0 0 0 0 +22 100 0 0 40 30 264 128 0 2.0 3.0 10 0.518 35.0 0 0 0 +21 100 0 0 40 30 156 80 0 2.0 3.0 10 0.584 30.0 0 0 0 +20 64 0 0 40 30 156 80 0 2.0 3.0 10 0.658 25.0 0 0 0 +19 64 0 0 40 30 92 56 0 2.0 3.0 10 0.711 22.0 0 0 0 +18 39 0 0 40 30 92 56 0 2.0 3.0 10 0.762 20.0 0 0 0 +17 39 0 0 40 30 56 36 0 2.0 3.0 10 0.8 18.0 0 0 0 +16 23 0 0 40 30 56 36 0 2.0 3.0 10 0.838 16.0 0 0 0 +15 23 0 0 40 30 32 24 0 2.0 3.0 10 0.871 14.0 0 0 0 +14 14 0 0 40 30 32 24 0 2.0 3.0 10 0.899 12.0 0 0 0 +13 14 0 0 40 30 20 16 0 2.0 3.0 10 0.922 10.0 0 0 0 +12 8 0 0 40 30 16 16 0 2.0 3.0 10 0.95 8.0 0 0 0 +11 7 0 0 40 30 12 12 0 2.0 3.0 10 0.963 6.0 0 0 0 +10 7 0 0 40 30 8 12 0 2.0 3.0 10 0.973 4.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/24.ENC b/configs/sim/axis/sedm/Etabs/24.ENC new file mode 100644 index 00000000000..e8445a6d9bc --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/24.ENC @@ -0,0 +1,17 @@ +24.ENC MM CU+ ST- DISPOWER not for oebiting +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 190 0 0 40 30 440 212 0 2.0 3.0 10 0.0 0.0 0 0 0 +24 180 0 0 40 30 440 212 0 2.0 3.0 10 0.0 45.0 0 0 0 +23 170 0 0 40 30 440 212 0 2.0 3.0 10 0.0 40.0 0 0 0 +22 160 0 0 40 30 440 212 0 2.0 3.0 10 0.0 35.0 0 0 0 +21 150 0 0 40 30 440 212 0 2.0 3.0 10 0.0 30.0 0 0 0 +20 140 0 0 40 30 440 212 0 2.0 3.0 10 0.0 25.0 0 0 0 +19 130 0 0 40 30 440 212 0 2.0 3.0 10 0.0 22.0 0 0 0 +18 120 0 0 40 30 440 212 0 2.0 3.0 10 0.0 20.0 0 0 0 +17 110 0 0 40 30 440 212 0 2.0 3.0 10 0.0 18.0 0 0 0 +16 100 0 0 40 30 440 212 0 2.0 3.0 10 0.0 16.0 0 0 0 +15 75 0 0 40 30 440 212 0 2.0 3.0 10 0.0 14.0 0 0 0 +14 50 0 0 40 30 440 212 0 2.0 3.0 10 0.0 12.0 0 0 0 +13 25 0 0 40 30 440 212 0 2.0 3.0 10 0.0 10.0 0 0 0 +12 12 0 0 40 30 440 212 0 2.0 3.0 10 0.0 8.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/28.ENC b/configs/sim/axis/sedm/Etabs/28.ENC new file mode 100644 index 00000000000..beb39745b56 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/28.ENC @@ -0,0 +1,6 @@ +28.ENC MM GR + ST - ~0.002"/s UNS may be run neg pol +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 8 0 0 40 30 8 12 0 3.6 1.4 10 0.051 0.0 0 0 0 +24 3 0 0 40 30 4 12 0 3.6 1.4 10 0.02 45.0 0 0 0 +23 1 0 0 40 30 4 12 0 3.6 1.4 10 0.028 40.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/29.ENC b/configs/sim/axis/sedm/Etabs/29.ENC new file mode 100644 index 00000000000..f3f12d520c8 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/29.ENC @@ -0,0 +1,10 @@ +29.ENC MM ~0.003"/s UNS low On with lo D% suggest carbide +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 12 0 0 45 35 8 16 0 3.6 1.4 10 0.076 0.0 0 0 0 +24 9 0 0 45 35 8 16 0 3.6 1.4 10 0.015 45.0 0 0 0 +23 4 0 0 45 35 8 16 0 3.6 2.0 10 0.028 40.0 0 0 0 +22 3 0 0 45 35 8 16 0 3.6 3.0 10 0.033 36.0 0 0 0 +21 2 0 0 45 35 8 16 0 3.6 4.0 10 0.041 32.0 0 0 0 +20 1 0 0 45 35 8 16 0 3.6 5.0 10 0.046 29.0 0 0 0 +19 1 0 0 40 30 4 12 0 3.6 6.0 10 0.053 26.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/30.ENC b/configs/sim/axis/sedm/Etabs/30.ENC new file mode 100644 index 00000000000..a50b341247b --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/30.ENC @@ -0,0 +1,11 @@ +30.ENC MM GR+ ST- ~0.004"/s UNS +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 16 0 0 55 45 16 12 0 3.6 1.4 10 0.102 0.0 0 0 0 +24 9 0 0 55 45 16 12 0 3.6 1.4 10 0.023 45.0 0 0 0 +23 5 0 0 55 45 16 12 0 3.6 2.0 10 0.038 40.0 0 0 0 +22 4 0 0 50 40 12 12 0 3.6 3.0 10 0.048 36.0 0 0 0 +21 3 0 0 45 35 8 12 0 3.6 4.0 10 0.058 32.0 0 0 0 +20 3 0 0 40 30 4 12 0 3.6 5.0 10 0.069 29.0 0 0 0 +19 2 0 0 40 30 4 12 0 3.6 6.0 10 0.074 26.0 0 0 0 +18 1 0 0 40 30 4 12 0 3.6 6.0 10 0.079 23.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/31.ENC b/configs/sim/axis/sedm/Etabs/31.ENC new file mode 100644 index 00000000000..b25efc4233f --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/31.ENC @@ -0,0 +1,13 @@ +31.ENC MM ~0.005"/side UNS maybe Carbide loe on loow D% lowIP +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 18 0 0 65 55 24 16 0 3.6 1.4 10 0.127 0.0 0 0 0 +24 11 0 0 50 40 24 12 0 3.6 1.4 10 0.025 45.0 0 0 0 +23 11 0 0 50 40 16 12 0 3.6 2.0 10 0.043 40.0 0 0 0 +22 6 0 0 50 40 16 12 0 3.6 3.0 10 0.058 36.0 0 0 0 +21 6 0 0 45 35 8 12 0 3.6 4.0 10 0.074 32.0 0 0 0 +20 4 0 0 45 35 8 12 0 3.6 5.0 10 0.079 29.0 0 0 0 +19 4 0 0 40 30 4 12 0 3.6 6.0 10 0.089 26.0 0 0 0 +18 3 0 0 40 30 4 12 0 3.6 6.0 10 0.094 23.0 0 0 0 +17 2 0 0 40 30 4 12 0 3.6 6.0 10 0.099 20.0 0 0 0 +16 1 0 0 40 30 4 12 0 3.6 6.0 10 0.104 17.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/32.ENC b/configs/sim/axis/sedm/Etabs/32.ENC new file mode 100644 index 00000000000..e212f4d2007 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/32.ENC @@ -0,0 +1,12 @@ +32.ENC MM ?? GR+ Wo - ?? ~0.006/s UNS maybe Carbide lo IP 76 D% med on tine or eoughuing +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 18 0 0 45 35 64 20 0 3.6 1.4 10 0.152 0.0 0 0 0 +24 16 0 0 50 40 48 24 0 3.6 1.4 10 0.02 45.0 0 0 0 +23 16 0 0 50 40 24 16 0 3.6 2.0 10 0.048 40.0 0 0 0 +22 16 0 0 50 40 12 12 0 3.6 3.0 10 0.069 36.0 0 0 0 +21 8 0 0 45 35 8 12 0 3.6 4.0 10 0.099 32.0 0 0 0 +20 8 0 0 40 30 4 12 0 3.6 5.0 10 0.112 29.0 0 0 0 +19 5 0 0 40 30 4 12 0 3.6 6.0 10 0.117 26.0 0 0 0 +18 3 0 0 40 30 4 12 0 3.6 6.0 10 0.122 23.0 0 0 0 +17 2 0 0 40 30 4 12 0 3.6 6.0 10 0.127 20.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/33.ENC b/configs/sim/axis/sedm/Etabs/33.ENC new file mode 100644 index 00000000000..715a9101bfa --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/33.ENC @@ -0,0 +1,17 @@ +33.ENC MM~0.008/s UNS +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 32 0 0 40 30 68 24 0 3.6 1.4 10 0.203 0.0 0 0 0 +24 25 0 0 45 35 56 20 0 3.6 1.4 10 0.028 45.0 0 0 0 +23 16 0 0 50 40 56 20 0 3.6 2.0 10 0.053 40.0 0 0 0 +22 15 0 0 50 40 36 16 0 3.6 3.0 10 0.076 36.0 0 0 0 +21 13 0 0 50 40 24 16 0 3.6 4.0 10 0.099 32.0 0 0 0 +20 12 0 0 50 40 16 12 0 3.6 5.0 10 0.114 29.0 0 0 0 +19 7 0 0 50 40 16 12 0 3.6 6.0 10 0.13 26.0 0 0 0 +18 6 0 0 50 40 12 12 0 3.6 6.0 10 0.14 23.0 0 0 0 +17 6 0 0 45 35 8 12 0 3.6 6.0 10 0.15 20.0 0 0 0 +16 3 0 0 45 35 8 12 0 3.6 6.0 10 0.157 17.0 0 0 0 +15 4 0 0 40 30 4 12 0 3.6 6.0 10 0.165 14.0 0 0 0 +14 3 0 0 40 30 4 12 0 3.6 6.0 10 0.17 12.0 0 0 0 +13 2 0 0 40 30 4 12 0 3.6 6.0 10 0.175 10.0 0 0 0 +12 1 0 0 40 30 4 12 0 3.6 6.0 10 0.18 8.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/34.ENC b/configs/sim/axis/sedm/Etabs/34.ENC new file mode 100644 index 00000000000..5e79fcf4024 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/34.ENC @@ -0,0 +1,14 @@ +34.ENC MM ~0,010"/s UNS GR+SR- +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 45 0 0 35 25 112 36 0 3.6 1.4 10 0.254 0.0 0 0 0 +24 28 0 0 40 30 100 36 0 3.6 1.4 10 0.046 45.0 0 0 0 +23 24 0 0 45 35 48 20 0 3.6 2.0 10 0.099 40.0 0 0 0 +22 20 0 0 45 35 24 12 0 3.6 3.0 10 0.14 36.0 0 0 0 +21 18 0 0 45 35 12 12 0 3.6 4.0 10 0.165 32.0 0 0 0 +20 16 0 0 45 35 8 12 0 3.6 5.0 10 0.18 29.0 0 0 0 +19 9 0 0 45 35 8 12 0 3.6 6.0 10 0.198 26.0 0 0 0 +18 10 0 0 40 30 4 12 0 3.6 6.0 10 0.208 23.0 0 0 0 +17 6 0 0 40 30 4 12 0 3.6 6.0 10 0.216 20.0 0 0 0 +16 4 0 0 40 30 4 12 0 3.6 6.0 10 0.221 17.0 0 0 0 +15 2 0 0 40 30 4 12 0 3.6 6.0 10 0.229 14.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/35.ENC b/configs/sim/axis/sedm/Etabs/35.ENC new file mode 100644 index 00000000000..7665e013b1c --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/35.ENC @@ -0,0 +1,16 @@ +35.ENC MM ~0.012"/s UNS GR+ ST- +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 63 0 0 32 22 112 32 0 3.6 1.4 10 0.305 0.0 0 0 0 +24 55 0 0 40 30 100 36 0 3.6 1.4 10 0.03 45.0 0 0 0 +23 35 0 0 45 35 100 36 0 3.6 2.0 10 0.069 40.0 0 0 0 +22 35 0 0 45 35 60 28 0 3.6 3.0 10 0.104 36.0 0 0 0 +21 21 0 0 45 35 60 28 0 3.6 4.0 10 0.14 32.0 0 0 0 +20 21 0 0 45 35 36 24 0 3.6 5.0 10 0.168 29.0 0 0 0 +19 12 0 0 45 35 36 24 0 3.6 6.0 10 0.196 26.0 0 0 0 +18 12 0 0 45 35 20 12 0 3.6 6.0 10 0.218 23.0 0 0 0 +17 8 0 0 45 35 20 12 0 3.6 6.0 10 0.231 20.0 0 0 0 +16 7 0 0 45 35 16 12 0 3.6 6.0 10 0.241 17.0 0 0 0 +15 5 0 0 45 35 12 12 0 3.6 6.0 10 0.254 14.0 0 0 0 +14 5 0 0 45 35 8 12 0 3.6 6.0 10 0.262 12.0 0 0 0 +13 5 0 0 40 30 4 12 0 3.6 6.0 10 0.274 10.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/41.ENC b/configs/sim/axis/sedm/Etabs/41.ENC new file mode 100644 index 00000000000..2c69bc4e199 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/41.ENC @@ -0,0 +1,13 @@ +41.ENC MM ~0.005/s UNS GR+ ST- +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 14 0 0 65 55 32 16 0 3.6 1.4 10 0.127 0.0 0 0 0 +24 14 0 0 50 40 20 12 0 3.6 1.4 10 0.023 45.0 0 0 0 +23 8 0 0 50 40 20 12 0 3.6 2.0 10 0.046 40.0 0 0 0 +22 8 0 0 50 40 16 12 0 3.6 3.0 10 0.053 36.0 0 0 0 +21 7 0 0 45 35 12 12 0 3.6 4.0 10 0.063 32.0 0 0 0 +20 7 0 0 45 35 8 12 0 3.6 5.0 10 0.074 29.0 0 0 0 +19 8 0 0 40 30 4 12 0 3.6 6.0 10 0.086 26.0 0 0 0 +18 5 0 0 40 30 4 12 0 3.6 6.0 10 0.091 23.0 0 0 0 +17 3 0 0 40 30 4 12 0 3.6 6.0 10 0.097 20.0 0 0 0 +16 1 0 0 40 30 4 12 0 3.6 6.0 10 0.104 17.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/42.ENC b/configs/sim/axis/sedm/Etabs/42.ENC new file mode 100644 index 00000000000..d2be7914d79 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/42.ENC @@ -0,0 +1,12 @@ +42.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 17 0 0 45 35 64 24 0 3.6 1.4 10 0.152 0.0 0 0 0 +24 12 0 0 50 40 64 24 0 3.6 1.4 10 0.023 45.0 0 0 0 +23 12 0 0 50 40 36 20 0 3.6 2.0 10 0.046 40.0 0 0 0 +22 12 0 0 50 40 20 12 0 3.6 3.0 10 0.066 36.0 0 0 0 +21 8 0 0 45 35 8 12 0 3.6 4.0 10 0.099 32.0 0 0 0 +20 8 0 0 40 30 4 12 0 3.6 5.0 10 0.112 29.0 0 0 0 +19 6 0 0 40 30 4 12 0 3.6 6.0 10 0.114 26.0 0 0 0 +18 4 0 0 40 30 4 12 0 3.6 6.0 10 0.119 20.0 0 0 0 +17 2 0 0 40 30 4 12 0 3.6 6.0 10 0.127 17.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/43.ENC b/configs/sim/axis/sedm/Etabs/43.ENC new file mode 100644 index 00000000000..22f5ebd6185 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/43.ENC @@ -0,0 +1,17 @@ +43.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 24 0 0 40 30 88 32 0 3.6 1.4 10 0.203 0.0 0 0 0 +24 22 0 0 45 35 56 20 0 3.6 1.4 10 0.036 45.0 0 0 0 +23 16 0 0 50 40 56 20 0 3.6 2.0 10 0.053 40.0 0 0 0 +22 15 0 0 50 40 36 16 0 3.6 3.0 10 0.076 36.0 0 0 0 +21 13 0 0 50 40 24 16 0 3.6 4.0 10 0.099 32.0 0 0 0 +20 12 0 0 50 40 16 16 0 3.6 5.0 10 0.114 29.0 0 0 0 +19 7 0 0 50 40 16 16 0 3.6 6.0 10 0.13 26.0 0 0 0 +18 6 0 0 50 40 12 12 0 3.6 6.0 10 0.14 23.0 0 0 0 +17 6 0 0 45 35 8 12 0 3.6 6.0 10 0.15 20.0 0 0 0 +16 3 0 0 45 35 8 12 0 3.6 6.0 10 0.157 17.0 0 0 0 +15 4 0 0 40 30 4 12 0 3.6 6.0 10 0.165 14.0 0 0 0 +14 3 0 0 40 30 4 12 0 3.6 6.0 10 0.17 12.0 0 0 0 +13 2 0 0 40 30 4 12 0 3.6 6.0 10 0.175 10.0 0 0 0 +12 1 0 0 40 30 4 12 0 3.6 6.0 10 0.18 8.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/44.ENC b/configs/sim/axis/sedm/Etabs/44.ENC new file mode 100644 index 00000000000..bb725b08f8a --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/44.ENC @@ -0,0 +1,14 @@ +44.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 37 0 0 30 20 136 44 0 3.6 1.4 10 0.254 0.0 0 0 0 +24 28 0 0 30 20 100 36 0 3.6 1.4 10 0.046 45.0 0 0 0 +23 24 0 0 30 20 48 20 0 3.6 2.0 10 0.099 40.0 0 0 0 +22 20 0 0 30 20 24 12 0 3.6 3.0 10 0.14 36.0 0 0 0 +21 18 0 0 30 20 12 12 0 3.6 4.0 10 0.165 32.0 0 0 0 +20 16 0 0 30 20 8 12 0 3.6 5.0 10 0.18 29.0 0 0 0 +19 9 0 0 30 20 8 12 0 3.6 6.0 10 0.198 26.0 0 0 0 +18 10 0 0 30 20 4 12 0 3.6 6.0 10 0.208 20.0 0 0 0 +17 6 0 0 30 20 4 12 0 3.6 6.0 10 0.216 17.0 0 0 0 +16 3 0 0 30 20 4 12 0 3.6 6.0 10 0.224 14.0 0 0 0 +15 2 0 0 30 20 4 12 0 3.6 6.0 10 0.229 12.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/45.ENC b/configs/sim/axis/sedm/Etabs/45.ENC new file mode 100644 index 00000000000..77253a5dc4e --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/45.ENC @@ -0,0 +1,16 @@ +45.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 55 0 0 32 22 136 44 0 3.6 1.4 10 0.305 0.0 0 0 0 +24 55 0 0 40 30 100 36 0 3.6 1.4 10 0.03 45.0 0 0 0 +23 35 0 0 45 35 100 36 0 3.6 2.0 10 0.069 40.0 0 0 0 +22 35 0 0 45 35 60 28 0 3.6 3.0 10 0.104 36.0 0 0 0 +21 21 0 0 45 35 60 28 0 3.6 4.0 10 0.14 32.0 0 0 0 +20 21 0 0 45 35 36 24 0 3.6 5.0 10 0.168 29.0 0 0 0 +19 12 0 0 45 35 36 24 0 3.6 6.0 10 0.196 26.0 0 0 0 +18 12 0 0 45 35 20 12 0 3.6 6.0 10 0.218 23.0 0 0 0 +17 8 0 0 45 35 20 12 0 3.6 6.0 10 0.231 20.0 0 0 0 +16 7 0 0 45 35 16 12 0 3.6 6.0 10 0.241 17.0 0 0 0 +15 5 0 0 45 35 12 12 0 3.6 6.0 10 0.254 14.0 0 0 0 +14 5 0 0 45 35 8 12 0 3.6 6.0 10 0.262 12.0 0 0 0 +13 5 0 0 40 30 4 12 0 3.6 6.0 10 0.274 10.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/46.ENC b/configs/sim/axis/sedm/Etabs/46.ENC new file mode 100644 index 00000000000..378aba5a1ec --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/46.ENC @@ -0,0 +1,17 @@ +46.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 89 0 0 32 22 136 44 0 3.6 1.4 10 0.406 0.0 0 0 0 +24 64 0 0 40 30 136 28 0 3.6 1.4 10 0.061 45.0 0 0 0 +23 50 0 0 45 35 136 28 0 3.6 2.0 10 0.097 40.0 0 0 0 +22 40 0 0 45 35 100 28 0 3.6 3.0 10 0.15 36.0 0 0 0 +21 30 0 0 45 35 80 24 0 3.6 4.0 10 0.196 32.0 0 0 0 +20 30 0 0 45 35 48 20 0 3.6 5.0 10 0.231 29.0 0 0 0 +19 24 0 0 45 35 36 16 0 3.6 6.0 10 0.262 23.0 0 0 0 +18 16 0 0 45 35 32 16 0 3.6 6.0 10 0.29 20.0 0 0 0 +17 12 0 0 45 35 20 12 0 3.6 6.0 10 0.32 17.0 0 0 0 +16 8 0 0 45 35 20 12 0 3.6 6.0 10 0.333 14.0 0 0 0 +15 6 0 0 45 35 16 12 0 3.6 6.0 10 0.345 12.0 0 0 0 +14 6 0 0 45 35 12 12 0 3.6 6.0 10 0.353 10.0 0 0 0 +13 6 0 0 45 35 8 12 0 3.6 6.0 10 0.363 8.0 0 0 0 +12 4 0 0 45 35 8 12 0 3.6 6.0 10 0.368 6.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/47.ENC b/configs/sim/axis/sedm/Etabs/47.ENC new file mode 100644 index 00000000000..58ad078cd22 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/47.ENC @@ -0,0 +1,17 @@ +47.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 100 0 0 32 22 136 32 0 3.6 1.4 10 0.457 0.0 0 0 0 +24 89 0 0 40 30 136 48 0 3.6 1.4 10 0.033 45.0 0 0 0 +23 64 0 0 40 30 136 48 0 3.6 2.0 10 0.097 40.0 0 0 0 +22 50 0 0 45 35 136 40 0 3.6 3.0 10 0.16 36.0 0 0 0 +21 40 0 0 45 35 100 36 0 3.6 4.0 10 0.211 32.0 0 0 0 +20 30 0 0 45 35 80 32 0 3.6 5.0 10 0.251 29.0 0 0 0 +19 30 0 0 45 35 44 20 0 3.6 6.0 10 0.29 26.0 0 0 0 +18 24 0 0 45 35 36 16 0 3.6 6.0 10 0.317 23.0 0 0 0 +17 16 0 0 45 35 32 16 0 3.6 6.0 10 0.345 20.0 0 0 0 +16 12 0 0 45 35 20 12 0 3.6 6.0 10 0.373 17.0 0 0 0 +15 8 0 0 45 35 20 12 0 3.6 6.0 10 0.386 14.0 0 0 0 +14 8 0 0 45 35 12 12 0 3.6 6.0 10 0.401 12.0 0 0 0 +13 5 0 0 45 35 12 12 0 3.6 6.0 10 0.409 10.0 0 0 0 +12 4 0 0 45 35 8 8 0 3.6 6.0 10 0.419 8.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/48.ENC b/configs/sim/axis/sedm/Etabs/48.ENC new file mode 100644 index 00000000000..66383cafca4 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/48.ENC @@ -0,0 +1,15 @@ +48.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 150 0 0 32 22 136 48 0 3.6 1.4 10 0.635 0.0 0 0 0 +24 120 0 0 40 30 136 48 0 3.6 1.4 10 0.132 45.0 0 0 0 +23 79 0 0 40 30 136 48 0 3.6 2.0 10 0.262 40.0 0 0 0 +22 60 0 0 40 30 136 48 0 3.6 3.0 10 0.325 36.0 0 0 0 +21 48 0 0 45 35 100 48 0 3.6 4.0 10 0.378 32.0 0 0 0 +20 35 0 0 45 35 80 24 0 3.6 5.0 10 0.424 29.0 0 0 0 +19 34 0 0 45 35 48 20 0 3.6 6.0 10 0.465 26.0 0 0 0 +18 24 0 0 45 35 36 16 0 3.6 6.0 10 0.503 23.0 0 0 0 +17 16 0 0 45 35 32 20 0 3.6 6.0 10 0.528 20.0 0 0 0 +16 12 0 0 45 35 20 12 0 3.6 6.0 10 0.556 17.0 0 0 0 +15 8 0 0 45 35 20 12 0 3.6 6.0 10 0.569 14.0 0 0 0 +14 6 0 0 45 35 16 16 0 3.6 6.0 10 0.582 12.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/49.ENC b/configs/sim/axis/sedm/Etabs/49.ENC new file mode 100644 index 00000000000..99dfcd01932 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/49.ENC @@ -0,0 +1,14 @@ +49.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 190 0 0 32 22 136 44 0 3.6 1.4 10 0.813 0.0 0 0 0 +24 140 0 0 40 30 136 48 0 3.6 1.4 10 0.239 45.0 0 0 0 +23 79 0 0 40 30 136 48 0 3.6 2.0 10 0.444 40.0 0 0 0 +22 60 0 0 40 30 136 48 0 3.6 3.0 10 0.511 36.0 0 0 0 +21 48 0 0 45 35 100 40 0 3.6 4.0 10 0.561 32.0 0 0 0 +20 35 0 0 45 35 80 32 0 3.6 5.0 10 0.605 29.0 0 0 0 +19 34 0 0 45 35 48 20 0 3.6 6.0 10 0.64 26.0 0 0 0 +18 24 0 0 45 35 36 16 0 3.6 6.0 10 0.678 23.0 0 0 0 +17 16 0 0 45 35 32 16 0 3.6 6.0 10 0.706 20.0 0 0 0 +16 12 0 0 45 35 20 16 0 3.6 6.0 10 0.737 17.0 0 0 0 +15 8 0 0 45 35 20 16 0 3.6 6.0 10 0.749 14.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/52.ENC b/configs/sim/axis/sedm/Etabs/52.ENC new file mode 100644 index 00000000000..66a46778b9c --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/52.ENC @@ -0,0 +1,12 @@ +52.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 14 0 0 45 35 80 28 0 3.6 1.4 10 0.152 0.0 0 0 0 +24 11 0 0 50 40 64 20 0 3.6 1.4 10 0.025 45.0 0 0 0 +23 11 0 0 50 40 36 20 0 3.6 2.0 10 0.048 40.0 0 0 0 +22 11 0 0 50 40 20 16 0 3.6 3.0 10 0.069 36.0 0 0 0 +21 8 0 0 45 35 8 12 0 3.6 4.0 10 0.099 32.0 0 0 0 +20 8 0 0 40 30 4 12 0 3.6 5.0 10 0.112 29.0 0 0 0 +19 6 0 0 40 30 4 12 0 3.6 6.0 10 0.114 26.0 0 0 0 +18 4 0 0 40 30 4 12 0 3.6 6.0 10 0.119 23.0 0 0 0 +17 2 0 0 40 30 4 12 0 3.6 6.0 10 0.127 20.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/53.ENC b/configs/sim/axis/sedm/Etabs/53.ENC new file mode 100644 index 00000000000..275576fabc5 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/53.ENC @@ -0,0 +1,17 @@ +53.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 20 0 0 40 30 104 28 0 3.6 1.4 10 0.203 0.0 0 0 0 +24 18 0 0 45 35 72 24 0 3.6 1.4 10 0.036 45.0 0 0 0 +23 16 0 0 50 40 56 20 0 3.6 2.0 10 0.053 40.0 0 0 0 +22 15 0 0 50 40 36 16 0 3.6 3.0 10 0.076 36.0 0 0 0 +21 13 0 0 50 40 24 16 0 3.6 4.0 10 0.099 32.0 0 0 0 +20 12 0 0 50 40 16 16 0 3.6 5.0 10 0.114 29.0 0 0 0 +19 7 0 0 50 40 16 16 0 3.6 6.0 10 0.13 26.0 0 0 0 +18 6 0 0 50 40 12 12 0 3.6 6.0 10 0.14 23.0 0 0 0 +17 6 0 0 50 40 8 12 0 3.6 6.0 10 0.15 20.0 0 0 0 +16 3 0 0 50 40 8 12 0 3.6 6.0 10 0.157 17.0 0 0 0 +15 4 0 0 45 35 4 12 0 3.6 6.0 10 0.165 14.0 0 0 0 +14 3 0 0 45 35 4 12 0 3.6 6.0 10 0.17 12.0 0 0 0 +13 2 0 0 40 30 4 12 0 3.6 6.0 10 0.175 10.0 0 0 0 +12 1 0 0 40 30 4 12 0 3.6 6.0 10 0.18 8.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/54.ENC b/configs/sim/axis/sedm/Etabs/54.ENC new file mode 100644 index 00000000000..70feeda381a --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/54.ENC @@ -0,0 +1,14 @@ +54.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 28 0 0 35 25 176 44 0 3.6 1.4 10 0.254 0.0 0 0 0 +24 28 0 0 40 30 100 36 0 3.6 1.4 10 0.046 15.0 0 0 0 +23 24 0 0 45 35 48 20 0 3.6 2.0 10 0.099 40.0 0 0 0 +22 20 0 0 45 35 24 12 0 3.6 3.0 10 0.14 36.0 0 0 0 +21 18 0 0 45 35 12 12 0 3.6 4.0 10 0.165 32.0 0 0 0 +20 16 0 0 45 35 8 12 0 3.6 5.0 10 0.18 29.0 0 0 0 +19 9 0 0 45 35 8 12 0 3.6 6.0 10 0.198 26.0 0 0 0 +18 10 0 0 40 30 4 12 0 3.6 6.0 10 0.208 23.0 0 0 0 +17 6 0 0 40 30 4 12 0 3.6 6.0 10 0.216 20.0 0 0 0 +16 4 0 0 40 30 4 12 0 3.6 6.0 10 0.221 17.0 0 0 0 +15 2 0 0 40 30 4 12 0 3.6 6.0 10 0.229 14.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/55.ENC b/configs/sim/axis/sedm/Etabs/55.ENC new file mode 100644 index 00000000000..7d52ce97320 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/55.ENC @@ -0,0 +1,16 @@ +55.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 43 0 0 32 22 176 48 0 3.6 1.4 10 0.305 0.0 0 0 0 +24 35 0 0 40 30 160 48 0 3.6 1.4 10 0.028 45.0 0 0 0 +23 35 0 0 45 35 100 36 0 3.6 2.0 10 0.069 40.0 0 0 0 +22 35 0 0 45 35 60 28 0 3.6 3.0 10 0.104 36.0 0 0 0 +21 21 0 0 45 35 60 28 0 3.6 4.0 10 0.14 32.0 0 0 0 +20 21 0 0 45 35 36 24 0 3.6 5.0 10 0.168 29.0 0 0 0 +19 12 0 0 45 35 36 24 0 3.6 6.0 10 0.196 26.0 0 0 0 +18 12 0 0 45 35 20 12 0 3.6 6.0 10 0.218 23.0 0 0 0 +17 8 0 0 45 35 20 12 0 3.6 6.0 10 0.231 20.0 0 0 0 +16 7 0 0 45 35 16 12 0 3.6 6.0 10 0.241 17.0 0 0 0 +15 5 0 0 45 35 12 12 0 3.6 6.0 10 0.254 14.0 0 0 0 +14 5 0 0 45 35 8 12 0 3.6 6.0 10 0.262 12.0 0 0 0 +13 5 0 0 45 35 4 12 0 3.6 6.0 10 0.274 10.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/56.ENC b/configs/sim/axis/sedm/Etabs/56.ENC new file mode 100644 index 00000000000..1ee989d7f21 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/56.ENC @@ -0,0 +1,17 @@ +56.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 79 0 0 32 22 176 56 0 3.6 1.4 10 0.406 0.0 0 0 0 +24 64 0 0 40 30 176 56 0 3.6 1.4 10 0.038 45.0 0 0 0 +23 50 0 0 45 35 136 48 0 3.6 2.0 10 0.097 40.0 0 0 0 +22 40 0 0 45 35 100 36 0 3.6 3.0 10 0.15 36.0 0 0 0 +21 30 0 0 45 35 80 32 0 3.6 4.0 10 0.196 32.0 0 0 0 +20 30 0 0 45 35 48 20 0 3.6 5.0 10 0.231 29.0 0 0 0 +19 24 0 0 45 35 36 16 0 3.6 6.0 10 0.262 26.0 0 0 0 +18 16 0 0 45 35 32 16 0 3.6 6.0 10 0.29 23.0 0 0 0 +17 12 0 0 45 35 20 12 0 3.6 6.0 10 0.32 20.0 0 0 0 +16 8 0 0 45 35 20 12 0 3.6 6.0 10 0.333 17.0 0 0 0 +15 6 0 0 45 35 16 12 0 3.6 6.0 10 0.345 14.0 0 0 0 +14 6 0 0 45 35 12 12 0 3.6 6.0 10 0.353 12.0 0 0 0 +13 6 0 0 45 35 8 12 0 3.6 6.0 10 0.363 10.0 0 0 0 +12 4 0 0 45 35 8 12 0 3.6 6.0 10 0.368 8.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/57.ENC b/configs/sim/axis/sedm/Etabs/57.ENC new file mode 100644 index 00000000000..b7119639d1a --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/57.ENC @@ -0,0 +1,17 @@ +57.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 100 0 0 32 22 176 56 0 3.6 1.4 10 0.457 0.0 0 0 0 +24 89 0 0 40 30 176 56 0 3.6 1.4 10 0.033 45.0 0 0 0 +23 64 0 0 40 30 176 56 0 3.6 2.0 10 0.097 40.0 0 0 0 +22 50 0 0 45 35 136 48 0 3.6 3.0 10 0.16 36.0 0 0 0 +21 40 0 0 45 35 100 36 0 3.6 4.0 10 0.211 32.0 0 0 0 +20 30 0 0 45 35 80 24 0 3.6 5.0 10 0.251 29.0 0 0 0 +19 30 0 0 45 35 44 20 0 3.6 6.0 10 0.29 26.0 0 0 0 +18 24 0 0 45 35 36 16 0 3.6 6.0 10 0.317 23.0 0 0 0 +17 16 0 0 45 35 32 16 0 3.6 6.0 10 0.345 20.0 0 0 0 +16 12 0 0 45 35 20 12 0 3.6 6.0 10 0.373 17.0 0 0 0 +15 8 0 0 45 35 20 12 0 3.6 6.0 10 0.386 14.0 0 0 0 +14 8 0 0 45 35 12 12 0 3.6 6.0 10 0.401 12.0 0 0 0 +13 5 0 0 45 35 12 12 0 3.6 6.0 10 0.409 10.0 0 0 0 +12 4 0 0 45 35 8 16 0 3.6 6.0 10 0.419 8.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/58.ENC b/configs/sim/axis/sedm/Etabs/58.ENC new file mode 100644 index 00000000000..38919c4c4c2 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/58.ENC @@ -0,0 +1,15 @@ +58.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 150 0 0 32 22 176 56 0 3.6 1.4 10 0.635 0.0 0 0 0 +24 120 0 0 40 30 176 60 0 3.6 1.4 10 0.132 45.0 0 0 0 +23 79 0 0 40 30 176 60 0 3.6 2.0 10 0.262 40.0 0 0 0 +22 60 0 0 40 30 136 48 0 3.6 3.0 10 0.325 36.0 0 0 0 +21 48 0 0 45 35 100 48 0 3.6 4.0 10 0.378 32.0 0 0 0 +20 35 0 0 45 35 80 24 0 3.6 5.0 10 0.424 29.0 0 0 0 +19 34 0 0 45 35 48 20 0 3.6 6.0 10 0.465 26.0 0 0 0 +18 24 0 0 45 35 36 16 0 3.6 6.0 10 0.503 23.0 0 0 0 +17 16 0 0 45 35 32 20 0 3.6 6.0 10 0.528 20.0 0 0 0 +16 12 0 0 45 35 20 12 0 3.6 6.0 10 0.556 17.0 0 0 0 +15 8 0 0 45 35 20 12 0 3.6 6.0 10 0.569 14.0 0 0 0 +14 6 0 0 45 35 16 16 0 3.6 6.0 10 0.582 12.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/59.ENC b/configs/sim/axis/sedm/Etabs/59.ENC new file mode 100644 index 00000000000..a74ddfac150 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/59.ENC @@ -0,0 +1,14 @@ +59.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 190 0 0 32 22 224 60 0 3.6 1.4 10 0.813 0.0 0 0 0 +24 140 0 0 40 30 224 60 0 3.6 1.4 10 0.239 45.0 0 0 0 +23 79 0 0 40 30 176 64 0 3.6 2.0 10 0.452 40.0 0 0 0 +22 60 0 0 40 30 136 48 0 3.6 3.0 10 0.513 36.0 0 0 0 +21 48 0 0 45 35 100 40 0 3.6 4.0 10 0.564 32.0 0 0 0 +20 35 0 0 45 35 80 32 0 3.6 5.0 10 0.605 29.0 0 0 0 +19 34 0 0 45 35 48 20 0 3.6 6.0 10 0.64 26.0 0 0 0 +18 24 0 0 45 35 36 16 0 3.6 6.0 10 0.678 23.0 0 0 0 +17 16 0 0 45 35 32 16 0 3.6 6.0 10 0.706 20.0 0 0 0 +16 12 0 0 45 35 20 16 0 3.6 6.0 10 0.737 17.0 0 0 0 +15 8 0 0 45 35 20 16 0 3.6 6.0 10 0.749 14.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/60.ENC b/configs/sim/axis/sedm/Etabs/60.ENC new file mode 100644 index 00000000000..a9b10b6e92a --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/60.ENC @@ -0,0 +1,8 @@ +60.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 18 1 0 50 40 16 36 0 3.6 1.4 10 0.102 0.0 0 0 0 +24 14 1 0 50 40 16 36 0 3.6 1.4 10 0.03 45.0 0 0 0 +23 12 1 0 50 40 12 28 0 3.6 2.0 10 0.051 40.0 0 0 0 +22 9 1 0 50 40 12 28 0 3.6 3.0 10 0.061 36.0 0 0 0 +21 6 1 0 50 40 12 28 0 3.6 4.0 10 0.069 32.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/61.ENC b/configs/sim/axis/sedm/Etabs/61.ENC new file mode 100644 index 00000000000..45ad81e12e0 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/61.ENC @@ -0,0 +1,9 @@ +61.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 50 1 0 32 22 20 48 0 3.6 1.4 10 0.152 0.0 0 0 0 +24 32 1 0 32 22 20 48 0 3.6 1.4 10 0.025 45.0 0 0 0 +23 32 1 0 32 22 12 28 0 3.6 2.0 10 0.053 40.0 0 0 0 +22 21 1 0 32 22 12 28 0 3.6 3.0 10 0.081 36.0 0 0 0 +21 12 1 0 32 22 12 28 0 3.6 4.0 10 0.097 32.0 0 0 0 +20 7 1 0 32 22 12 28 0 3.6 5.0 10 0.107 29.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/62.ENC b/configs/sim/axis/sedm/Etabs/62.ENC new file mode 100644 index 00000000000..39df33c3242 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/62.ENC @@ -0,0 +1,11 @@ +62.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 65 1 0 32 22 36 64 0 3.6 1.4 10 0.203 0.0 0 0 0 +24 40 1 0 32 22 36 56 0 3.6 1.4 10 0.051 45.0 0 0 0 +23 40 1 0 32 22 24 48 0 3.6 2.0 10 0.074 40.0 0 0 0 +22 23 1 0 32 22 24 48 0 3.6 3.0 10 0.102 36.0 0 0 0 +21 23 1 0 32 22 16 24 0 3.6 4.0 10 0.135 32.0 0 0 0 +20 14 1 0 32 22 16 24 0 3.6 5.0 10 0.147 29.0 0 0 0 +19 14 1 0 32 22 12 20 0 3.6 6.0 10 0.16 26.0 0 0 0 +18 8 1 0 32 22 12 20 0 3.6 6.0 10 0.17 23.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/63.ENC b/configs/sim/axis/sedm/Etabs/63.ENC new file mode 100644 index 00000000000..a4e3d81f23c --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/63.ENC @@ -0,0 +1,11 @@ +63.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 75 1 0 32 22 36 48 0 3.6 1.4 10 0.305 0.0 0 0 0 +24 45 1 0 32 22 36 36 0 3.6 1.4 10 0.076 45.0 0 0 0 +23 30 1 0 32 22 24 36 0 3.6 2.0 10 0.114 40.0 0 0 0 +22 30 1 0 32 22 16 24 0 3.6 3.0 10 0.178 36.0 0 0 0 +21 18 1 0 32 22 16 24 0 3.6 4.0 10 0.229 32.0 0 0 0 +20 18 1 0 32 22 12 20 0 3.6 5.0 10 0.254 29.0 0 0 0 +19 10 1 0 32 22 12 20 0 3.6 6.0 10 0.264 26.0 0 0 0 +18 6 1 0 32 22 12 20 0 3.6 6.0 10 0.272 23.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/64.ENC b/configs/sim/axis/sedm/Etabs/64.ENC new file mode 100644 index 00000000000..412ed78c38d --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/64.ENC @@ -0,0 +1,8 @@ +64.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 20 1 0 60 50 20 80 0 3.6 1.4 10 0.102 0.0 0 0 0 +24 20 1 0 60 50 16 64 0 3.6 1.4 10 0.03 45.0 0 0 0 +23 12 1 0 60 50 12 48 0 3.6 2.0 10 0.051 40.0 0 0 0 +22 9 1 0 60 50 12 48 0 3.6 3.0 10 0.061 36.0 0 0 0 +21 6 1 0 60 50 12 48 0 3.6 4.0 10 0.069 32.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/65.ENC b/configs/sim/axis/sedm/Etabs/65.ENC new file mode 100644 index 00000000000..812ffa5fc75 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/65.ENC @@ -0,0 +1,9 @@ +65.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 60 1 0 60 50 20 80 0 3.6 1.4 10 0.152 0.0 0 0 0 +24 36 1 0 60 50 20 80 0 3.6 1.4 10 0.025 45.0 0 0 0 +23 36 1 0 60 50 12 48 0 3.6 2.0 10 0.053 40.0 0 0 0 +22 21 1 0 60 50 12 48 0 3.6 3.0 10 0.081 36.0 0 0 0 +21 12 1 0 60 50 12 48 0 3.6 4.0 10 0.097 32.0 0 0 0 +20 7 1 0 60 50 12 48 0 3.6 5.0 10 0.107 29.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/66.ENC b/configs/sim/axis/sedm/Etabs/66.ENC new file mode 100644 index 00000000000..21d0aa7f26c --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/66.ENC @@ -0,0 +1,11 @@ +66.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 65 1 0 60 50 36 144 0 3.6 1.4 10 0.203 0.0 0 0 0 +24 40 1 0 60 50 36 144 0 3.6 1.4 10 0.051 45.0 0 0 0 +23 40 1 0 60 50 24 96 0 3.6 2.0 10 0.074 40.0 0 0 0 +22 23 1 0 60 50 24 96 0 3.6 3.0 10 0.102 36.0 0 0 0 +21 23 1 0 60 50 16 64 0 3.6 4.0 10 0.135 32.0 0 0 0 +20 14 1 0 60 50 16 64 0 3.6 5.0 10 0.147 29.0 0 0 0 +19 14 1 0 60 50 12 36 0 3.6 6.0 10 0.16 26.0 0 0 0 +18 8 1 0 60 50 12 36 0 3.6 6.0 10 0.17 23.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/67.ENC b/configs/sim/axis/sedm/Etabs/67.ENC new file mode 100644 index 00000000000..a6b18e63597 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/67.ENC @@ -0,0 +1,11 @@ +67.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 35 0 2 75 65 40 80 0 1.0 2.0 10 0.127 0.0 0 0 0 +24 24 0 2 75 65 40 80 0 1.0 3.0 10 0.025 45.0 0 0 0 +23 24 0 2 75 65 24 48 0 1.0 3.5 10 0.041 40.0 0 0 0 +22 18 0 2 75 65 24 48 0 1.0 3.5 10 0.063 36.0 0 0 0 +21 18 0 2 75 65 20 40 0 1.0 3.5 10 0.076 32.0 0 0 0 +20 12 0 2 75 65 20 40 0 1.0 3.5 10 0.086 29.0 0 0 0 +19 8 0 2 75 65 20 40 0 1.0 3.5 10 0.094 26.0 0 0 0 +18 8 0 2 75 65 16 32 0 1.0 3.5 10 0.102 23.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/68.ENC b/configs/sim/axis/sedm/Etabs/68.ENC new file mode 100644 index 00000000000..0c342f38d09 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/68.ENC @@ -0,0 +1,12 @@ +68.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 60 0 0 30 20 148 168 0 3.6 3.5 10 0.406 0.0 0 0 0 +24 50 0 0 30 20 80 120 0 3.6 3.5 10 0.147 45.0 0 0 0 +23 35 0 0 30 20 48 72 0 3.6 3.5 10 0.249 40.0 0 0 0 +22 24 0 0 30 20 24 36 0 3.6 3.5 10 0.292 36.0 0 0 0 +21 20 0 0 30 20 12 24 0 3.6 3.5 10 0.323 32.0 0 0 0 +20 16 0 0 30 20 8 16 0 3.6 3.5 10 0.335 29.0 0 0 0 +19 8 0 0 30 20 4 12 0 3.6 3.5 10 0.351 26.0 0 0 0 +18 8 0 0 30 20 4 12 0 3.6 3.5 10 0.373 23.0 0 0 0 +17 6 0 0 30 20 4 12 0 3.6 3.5 10 0.378 20.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/69.ENC b/configs/sim/axis/sedm/Etabs/69.ENC new file mode 100644 index 00000000000..2a2be3529ec --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/69.ENC @@ -0,0 +1,12 @@ +69.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 24 0 0 25 15 112 140 0 3.6 3.5 10 0.254 0.0 0 0 0 +24 24 0 0 30 20 48 72 0 3.6 3.5 10 0.069 45.0 0 0 0 +23 20 0 0 30 20 24 36 0 3.6 3.5 10 0.109 40.0 0 0 0 +22 16 0 0 30 20 12 24 0 3.6 3.5 10 0.145 36.0 0 0 0 +21 12 0 0 30 20 12 24 0 3.6 3.5 10 0.173 32.0 0 0 0 +20 8 0 0 30 20 8 16 0 3.6 3.5 10 0.193 29.0 0 0 0 +19 4 0 0 30 20 4 12 0 3.6 3.5 10 0.206 26.0 0 0 0 +18 4 0 0 30 20 4 12 0 3.6 3.5 10 0.221 23.0 0 0 0 +17 2 0 0 30 20 4 12 0 3.6 3.5 10 0.224 20.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/70.ENC b/configs/sim/axis/sedm/Etabs/70.ENC new file mode 100644 index 00000000000..d3f60f22bf0 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/70.ENC @@ -0,0 +1,12 @@ +70.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 16 0 0 25 15 120 140 0 3.6 3.5 10 0.203 0.0 0 0 0 +24 16 0 0 30 20 48 72 0 3.6 3.5 10 0.061 45.0 0 0 0 +23 16 0 0 30 20 24 36 0 3.6 3.5 10 0.097 40.0 0 0 0 +22 16 0 0 30 20 12 24 0 3.6 3.5 10 0.124 36.0 0 0 0 +21 8 0 0 30 20 8 16 0 3.6 3.5 10 0.14 32.0 0 0 0 +20 8 0 0 30 20 4 12 0 3.6 3.5 10 0.152 29.0 0 0 0 +19 6 0 0 30 20 4 12 0 3.6 3.5 10 0.165 26.0 0 0 0 +18 4 0 0 30 20 4 12 0 3.6 3.5 10 0.173 23.0 0 0 0 +17 2 0 0 30 20 4 12 0 3.6 3.5 10 0.178 20.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/71.ENC b/configs/sim/axis/sedm/Etabs/71.ENC new file mode 100644 index 00000000000..6e44dbf3124 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/71.ENC @@ -0,0 +1,14 @@ +71.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 16 0 0 45 35 60 112 0 3.6 1.4 10 0.203 0.0 0 0 0 +24 12 0 0 45 35 60 112 0 3.6 1.4 10 0.025 45.0 0 0 0 +23 11 0 0 40 30 40 80 0 3.6 1.8 10 0.051 40.0 0 0 0 +22 9 0 0 40 30 36 72 0 3.6 2.0 10 0.076 36.0 0 0 0 +21 9 0 0 40 30 24 48 0 3.6 3.0 10 0.089 32.0 0 0 0 +20 8 0 0 40 30 16 32 0 3.6 4.0 10 0.102 229.0 0 0 0 +19 6 0 0 40 30 12 24 0 3.6 4.0 10 0.127 26.0 0 0 0 +18 5 0 0 40 30 8 16 0 3.6 4.0 10 0.14 23.0 0 0 0 +17 3 0 0 40 30 8 16 0 3.6 4.0 10 0.152 20.0 0 0 0 +16 3 0 0 35 25 4 8 0 3.6 4.0 10 0.165 17.0 0 0 0 +15 1 0 0 35 25 4 8 0 3.6 4.0 10 0.173 14.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/72.ENC b/configs/sim/axis/sedm/Etabs/72.ENC new file mode 100644 index 00000000000..b36fd65dfe6 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/72.ENC @@ -0,0 +1,4 @@ +72.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 20 1 0 30 20 200 144 0 3.6 6.0 10 0.076 0.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/73.ENC b/configs/sim/axis/sedm/Etabs/73.ENC new file mode 100644 index 00000000000..9913b4d4a34 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/73.ENC @@ -0,0 +1,9 @@ +73.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 55 1 0 35 25 76 100 0 3.6 3.5 10 0.254 0.0 0 0 0 +24 30 1 0 35 25 76 80 0 3.6 3.5 10 0.071 45.0 0 0 0 +23 24 1 0 35 25 60 48 0 3.6 3.5 10 0.119 40.0 0 0 0 +22 20 1 0 35 25 24 24 0 3.6 3.5 10 0.17 36.0 0 0 0 +21 18 1 0 35 25 12 12 0 3.6 3.5 10 0.206 32.0 0 0 0 +20 16 1 0 35 25 8 8 0 3.6 3.5 10 0.229 29.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/74.ENC b/configs/sim/axis/sedm/Etabs/74.ENC new file mode 100644 index 00000000000..abd9b2adf17 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/74.ENC @@ -0,0 +1,11 @@ +74.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 30 0 2 30 20 40 56 0 1.0 3.5 10 0.127 0.0 0 0 0 +24 18 0 2 30 20 16 24 0 1.0 3.5 10 0.013 45.0 0 0 0 +23 12 0 2 30 20 12 20 0 1.0 3.5 10 0.025 40.0 0 0 0 +22 8 0 2 30 20 8 12 0 1.0 3.5 10 0.043 36.0 0 0 0 +21 6 0 2 30 20 8 12 0 1.0 3.5 10 0.061 32.0 0 0 0 +20 3 0 2 30 20 8 12 0 1.0 3.5 10 0.076 29.0 0 0 0 +19 2 0 2 30 20 8 12 0 1.0 3.5 10 0.086 26.0 0 0 0 +18 1 0 2 30 20 4 8 0 1.0 3.5 10 0.094 23.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/75.ENC b/configs/sim/axis/sedm/Etabs/75.ENC new file mode 100644 index 00000000000..3384b6b2a4b --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/75.ENC @@ -0,0 +1,4 @@ +75.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 50 1 0 30 20 24 96 0 3.6 6.0 10 0.076 0.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/76.ENC b/configs/sim/axis/sedm/Etabs/76.ENC new file mode 100644 index 00000000000..2061d1375f8 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/76.ENC @@ -0,0 +1,14 @@ +76.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 35 0 0 35 25 100 120 0 3.6 3.5 10 0.305 0.0 0 0 0 +24 20 0 0 30 20 100 120 0 3.6 3.5 10 0.038 45.0 0 0 0 +23 15 0 0 30 20 80 100 0 3.6 3.5 10 0.069 40.0 0 0 0 +22 15 0 0 30 20 48 60 0 3.6 3.5 10 0.114 36.0 0 0 0 +21 8 0 0 30 20 48 60 0 3.6 3.5 10 0.173 32.0 0 0 0 +20 8 0 0 30 20 28 40 0 3.6 3.5 10 0.203 29.0 0 0 0 +19 4 0 0 30 20 28 40 0 3.6 3.5 10 0.224 26.0 0 0 0 +18 4 0 0 30 20 16 24 0 3.6 3.5 10 0.241 23.0 0 0 0 +17 2 0 0 30 20 12 16 0 3.6 3.5 10 0.259 20.0 0 0 0 +16 2 0 0 30 20 8 12 0 3.6 3.5 10 0.267 17.0 0 0 0 +15 1 0 0 30 20 4 12 0 3.6 3.5 10 0.274 14.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/77.ENC b/configs/sim/axis/sedm/Etabs/77.ENC new file mode 100644 index 00000000000..0c810b6a828 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/77.ENC @@ -0,0 +1,9 @@ +77.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 8 0 0 50 40 28 36 0 3.6 3.5 10 0.152 0.0 0 0 0 +24 5 0 0 40 30 28 36 0 3.6 3.5 10 0.02 45.0 0 0 0 +23 3 0 0 40 30 16 28 0 3.6 3.5 10 0.056 40.0 0 0 0 +22 3 0 0 40 30 8 12 0 3.6 3.5 10 0.086 36.0 0 0 0 +21 2 0 0 40 30 4 12 0 3.6 3.5 10 0.109 32.0 0 0 0 +20 1 0 0 40 30 4 12 0 3.6 3.5 10 0.122 29.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/78.ENC b/configs/sim/axis/sedm/Etabs/78.ENC new file mode 100644 index 00000000000..d3b1d00ce29 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/78.ENC @@ -0,0 +1,11 @@ +78.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 6 0 1 60 50 328 16 0 3.6 2.0 10 0.152 0.0 0 0 0 +24 4 0 1 50 40 200 12 0 3.6 2.0 10 0.025 45.0 0 0 0 +23 4 0 1 50 40 128 12 0 3.6 3.0 10 0.058 40.0 0 0 0 +22 2 0 1 50 40 128 12 0 3.6 4.0 10 0.084 36.0 0 0 0 +21 2 0 1 50 40 60 12 0 3.6 4.0 10 0.099 32.0 0 0 0 +20 2 0 1 50 40 36 16 0 3.6 4.0 10 0.112 29.0 0 0 0 +19 1 0 1 50 40 24 16 0 3.6 4.0 10 0.124 26.0 0 0 0 +18 1 0 1 50 40 16 16 0 3.6 4.0 10 0.13 23.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/79.ENC b/configs/sim/axis/sedm/Etabs/79.ENC new file mode 100644 index 00000000000..b99588e3a62 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/79.ENC @@ -0,0 +1,13 @@ +79.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 12 0 1 40 30 396 16 0 3.6 2.0 10 0.203 0.0 0 0 0 +24 8 0 1 40 30 328 16 0 3.6 2.0 10 0.033 45.0 0 0 0 +23 5 0 1 40 30 260 12 0 3.6 3.0 10 0.061 40.0 0 0 0 +22 4 0 1 40 30 200 12 0 3.6 4.0 10 0.084 36.0 0 0 0 +21 3 0 1 40 30 200 12 0 3.6 4.0 10 0.107 32.0 0 0 0 +20 3 0 1 50 40 128 12 0 3.6 4.0 10 0.13 29.0 0 0 0 +19 2 0 1 50 40 104 12 0 3.6 4.0 10 0.15 26.0 0 0 0 +18 1 0 1 50 40 60 12 0 3.6 4.0 10 0.163 23.0 0 0 0 +17 1 0 1 50 40 28 16 0 3.6 4.0 10 0.175 20.0 0 0 0 +16 1 0 1 50 40 16 16 0 3.6 4.0 10 0.18 17.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/80.ENC b/configs/sim/axis/sedm/Etabs/80.ENC new file mode 100644 index 00000000000..33a45a3ae78 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/80.ENC @@ -0,0 +1,14 @@ +80.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 15 0 1 40 30 396 24 0 3.6 2.0 10 0.254 0.0 0 0 0 +24 12 0 1 40 30 396 24 0 3.6 2.0 10 0.043 45.0 0 0 0 +23 10 0 1 40 30 328 16 0 3.6 3.0 10 0.091 40.0 0 0 0 +22 8 0 1 40 30 328 16 0 3.6 4.0 10 0.114 36.0 0 0 0 +21 5 0 1 40 30 260 12 0 3.6 4.0 10 0.137 32.0 0 0 0 +20 4 0 1 40 30 200 12 0 3.6 4.0 10 0.155 29.0 0 0 0 +19 3 0 1 40 30 128 12 0 3.6 4.0 10 0.18 26.0 0 0 0 +18 2 0 1 40 30 104 12 0 3.6 4.0 10 0.196 23.0 0 0 0 +17 1 0 1 50 40 48 12 0 3.6 4.0 10 0.211 20.0 0 0 0 +16 1 0 1 50 40 28 16 0 3.6 4.0 10 0.224 17.0 0 0 0 +15 1 0 1 50 40 16 16 0 3.6 4.0 10 0.231 14.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/81.ENC b/configs/sim/axis/sedm/Etabs/81.ENC new file mode 100644 index 00000000000..f27404ce396 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/81.ENC @@ -0,0 +1,10 @@ +81.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 15 1 0 80 70 16 48 0 3.6 2.0 10 0.102 0.0 0 0 0 +24 10 1 0 80 70 16 48 0 3.6 2.0 10 0.03 45.0 0 0 0 +23 10 1 0 75 65 12 36 0 3.6 2.0 10 0.048 40.0 0 0 0 +22 5 1 0 75 65 12 36 0 3.6 2.0 10 0.063 36.0 0 0 0 +21 5 1 0 70 60 8 24 0 3.6 2.0 10 0.069 32.0 0 0 0 +20 3 1 0 70 60 8 24 0 3.6 2.0 10 0.079 29.0 0 0 0 +19 3 1 0 70 60 4 12 0 3.6 2.0 10 0.086 26.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/82.ENC b/configs/sim/axis/sedm/Etabs/82.ENC new file mode 100644 index 00000000000..890050a2d84 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/82.ENC @@ -0,0 +1,13 @@ +82.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 14 0 1 90 80 40 112 0 3.6 1.4 10 0.152 0.0 0 0 0 +24 7 0 1 90 80 40 112 0 3.6 1.4 10 0.03 45.0 0 0 0 +23 7 0 1 60 50 20 36 0 3.6 1.8 10 0.051 40.0 0 0 0 +22 4 0 1 60 50 20 36 0 3.6 2.0 10 0.066 36.0 0 0 0 +21 4 0 1 60 50 12 20 0 3.6 3.0 10 0.079 32.0 0 0 0 +20 3 0 1 60 50 12 20 0 3.6 4.0 10 0.089 29.0 0 0 0 +19 3 0 1 60 50 8 12 0 3.6 4.0 10 0.097 26.0 0 0 0 +18 2 0 1 60 50 8 12 0 3.6 4.0 10 0.107 23.0 0 0 0 +17 3 0 1 60 50 4 8 0 3.6 4.0 10 0.117 20.0 0 0 0 +16 2 0 1 60 50 4 8 0 3.6 4.0 10 0.127 17.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/90.ENC b/configs/sim/axis/sedm/Etabs/90.ENC new file mode 100644 index 00000000000..0988317ee00 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/90.ENC @@ -0,0 +1,15 @@ +90.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 21 0 1 90 80 40 112 0 3.6 1.4 10 0.203 0.0 0 0 0 +24 14 0 1 90 80 40 112 0 3.6 1.4 10 0.025 45.0 0 0 0 +23 11 0 1 60 50 24 36 0 3.6 2.0 10 0.061 40.0 0 0 0 +22 7 0 1 60 50 24 36 0 3.6 3.0 10 0.081 36.0 0 0 0 +21 7 0 1 50 40 16 20 0 3.6 4.0 10 0.097 32.0 0 0 0 +20 8 0 1 50 40 8 12 0 3.6 4.0 10 0.117 29.0 0 0 0 +19 5 0 1 50 40 8 12 0 3.6 4.0 10 0.127 26.0 0 0 0 +18 4 0 1 50 40 8 12 0 3.6 4.0 10 0.142 23.0 0 0 0 +17 3 0 1 50 40 8 12 0 3.6 4.0 10 0.152 20.0 0 0 0 +16 4 0 1 50 40 4 8 0 3.6 4.0 10 0.165 17.0 0 0 0 +15 3 0 1 50 40 4 8 0 3.6 4.0 10 0.17 14.0 0 0 0 +14 2 0 1 50 40 4 8 0 3.6 4.0 10 0.178 12.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/91.ENC b/configs/sim/axis/sedm/Etabs/91.ENC new file mode 100644 index 00000000000..bc66d8de410 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/91.ENC @@ -0,0 +1,15 @@ +91.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 28 0 1 70 60 44 112 0 3.6 1.4 10 0.254 0.0 0 0 0 +24 16 0 1 90 80 44 112 0 3.6 1.4 10 0.041 45.0 0 0 0 +23 16 0 1 60 50 28 44 0 3.6 2.0 10 0.076 40.0 0 0 0 +22 10 0 1 60 50 28 44 0 3.6 3.0 10 0.107 36.0 0 0 0 +21 10 0 1 50 40 20 24 0 3.6 4.0 10 0.127 32.0 0 0 0 +20 7 0 1 50 40 20 24 0 3.6 4.0 10 0.145 29.0 0 0 0 +19 6 0 1 45 35 12 12 0 3.6 4.0 10 0.175 26.0 0 0 0 +18 4 0 1 45 35 12 12 0 3.6 4.0 10 0.185 23.0 0 0 0 +17 5 0 1 45 35 8 12 0 3.6 4.0 10 0.196 20.0 0 0 0 +16 2 0 1 40 30 4 8 0 3.6 4.0 10 0.211 17.0 0 0 0 +15 4 0 1 40 30 4 8 0 3.6 4.0 10 0.218 14.0 0 0 0 +14 3 0 1 40 30 4 8 0 3.6 4.0 10 0.226 12.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/92.ENC b/configs/sim/axis/sedm/Etabs/92.ENC new file mode 100644 index 00000000000..92cb33afea9 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/92.ENC @@ -0,0 +1,14 @@ +92.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 55 0 1 90 80 44 112 0 3.6 1.4 10 0.305 0.0 0 0 0 +24 30 0 1 90 80 44 112 0 3.6 1.4 10 0.109 45.0 0 0 0 +23 24 0 1 80 70 48 100 0 3.6 2.0 10 0.142 40.0 0 0 0 +22 20 0 1 80 70 24 36 0 3.6 3.0 10 0.185 36.0 0 0 0 +21 18 0 1 80 70 12 16 0 3.6 4.0 10 0.213 32.0 0 0 0 +20 16 0 1 80 70 8 16 0 3.6 4.0 10 0.231 29.0 0 0 0 +19 12 0 1 80 70 8 16 0 3.6 4.0 10 0.241 26.0 0 0 0 +18 8 0 1 80 70 4 12 0 3.6 4.0 10 0.264 23.0 0 0 0 +17 6 0 1 80 70 4 12 0 3.6 4.0 10 0.267 20.0 0 0 0 +16 2 0 1 80 70 4 12 0 3.6 4.0 10 0.277 17.0 0 0 0 +15 1 0 1 80 70 4 12 0 3.6 4.0 10 0.282 14.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/93.ENC b/configs/sim/axis/sedm/Etabs/93.ENC new file mode 100644 index 00000000000..b9e847b9ec4 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/93.ENC @@ -0,0 +1,12 @@ +93.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 12 0 1 90 80 24 96 0 2.0 1.2 10 0.152 0.0 0 0 0 +24 12 0 1 90 80 16 56 0 2.0 1.4 10 0.03 45.0 0 0 0 +23 10 0 1 90 80 16 56 0 2.0 1.4 10 0.063 40.0 0 0 0 +22 10 0 1 70 60 12 36 0 2.0 1.8 10 0.081 36.0 0 0 0 +21 8 0 1 70 60 8 24 0 2.0 1.8 10 0.099 32.0 0 0 0 +20 8 0 1 70 60 4 16 0 2.0 1.8 10 0.112 29.0 0 0 0 +19 4 0 1 60 50 4 16 0 2.0 1.8 10 0.117 26.0 0 0 0 +18 3 0 1 60 50 4 16 0 2.0 1.8 10 0.122 23.0 0 0 0 +17 2 0 1 60 50 4 16 0 2.0 1.8 10 0.127 20.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/94.ENC b/configs/sim/axis/sedm/Etabs/94.ENC new file mode 100644 index 00000000000..6cb80507234 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/94.ENC @@ -0,0 +1,10 @@ +94.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 12 0 1 32 22 8 200 0 3.6 1.4 10 0.076 0.0 0 0 0 +24 9 0 1 65 55 8 16 0 3.6 1.4 10 0.015 45.0 0 0 0 +23 4 0 1 65 55 8 16 0 3.6 2.0 10 0.028 30.0 0 0 0 +22 3 0 1 65 55 8 16 0 3.6 3.0 10 0.033 20.0 0 0 0 +21 2 0 1 65 55 8 16 0 3.6 3.0 10 0.041 10.0 0 0 0 +20 1 0 1 65 55 8 16 0 3.6 3.0 10 0.046 5.0 0 0 0 +19 1 0 1 65 55 8 12 0 3.6 3.0 10 0.051 3.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Etabs/99.ENC b/configs/sim/axis/sedm/Etabs/99.ENC new file mode 100644 index 00000000000..ba718acddd8 --- /dev/null +++ b/configs/sim/axis/sedm/Etabs/99.ENC @@ -0,0 +1,12 @@ +99.ENC MM +NR IP P HV GVHI GVLO TON TOF ISO AJD ET CB RAD SPA VDI VE VW +25 18 0 0 45 35 64 20 0 3.6 1.4 10 0.152 0.0 0 0 0 +24 16 0 0 50 40 48 24 0 3.6 1.4 10 0.02 45.0 0 0 0 +23 16 0 0 50 40 24 16 0 3.6 2.0 10 0.048 40.0 0 0 0 +22 16 0 0 50 40 12 12 0 3.6 3.0 10 0.069 36.0 0 0 0 +21 8 0 0 45 35 8 12 0 3.6 4.0 10 0.099 32.0 0 0 0 +20 8 0 0 40 30 4 12 0 3.6 5.0 10 0.112 29.0 0 0 0 +19 5 0 0 40 30 4 12 0 3.6 6.0 10 0.117 26.0 0 0 0 +18 3 0 0 40 30 4 12 0 3.6 6.0 10 0.122 23.0 0 0 0 +17 2 0 0 40 30 4 12 0 3.6 6.0 10 0.127 20.0 0 0 0 +[END] diff --git a/configs/sim/axis/sedm/Mcodes/M160 b/configs/sim/axis/sedm/Mcodes/M160 new file mode 100755 index 00000000000..ebc8d383073 --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M160 @@ -0,0 +1,17 @@ +#!/bin/bash +# 22.11.2025 WAS only SET eTABnUM +# CHGD TO p ETABNUM q MSRDuns + +exec >/dev/null 2>&1 # Redirects all stdout and stderr for the rest of the + +# usage +# M160 P Q + +# EtabNum, will become a U32 ( bash always give a f;loat) +# vvv trick to cnvrt Float to INT (U32) +printf -v EtabNumInt '%d' "$1" +halcmd sets dEtabNum $EtabNumInt + +halcmd sets dMsrdUNSf $2 + +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M161 b/configs/sim/axis/sedm/Mcodes/M161 new file mode 100755 index 00000000000..3fa2979c674 --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M161 @@ -0,0 +1,24 @@ +#!/bin/bash + +exec >/dev/null 2>&1 # Redirects all stdout and stderr for the rest of the + +#21.08.2025 M161 + +# usage +# M161 P Q +# BegNR is U32 must be >= EndNR +# EndNR is U32 must be <= BegNR + +# and Bash retns Floaats +# so this vvv print trick cnvrts f2i +printf -v BegNRint '%d' "$1" + +# no more GUI BegNR nor EndNR +# this makes techGui smaller +# and fit next to std ZXIS gui +halcmd setp SEDM.BegNR $BegNRint + +printf -v EndNRint '%d' "$2" +halcmd setp SEDM.EndNR $EndNRint + +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M162 b/configs/sim/axis/sedm/Mcodes/M162 new file mode 100755 index 00000000000..e99f4c7b3cb --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M162 @@ -0,0 +1,53 @@ +#!/bin/bash +# 24.11.2025 test the value reciorded is as expected POS NEG or ZERO + +# vvv this will silebvce bash, handy when i use pruntf to cnvrt strg to float +#exec >/dev/null 2>&1 # Redirects all stdout and stderr for the rest of the + +# usage +# M162 P Q + +#halcmd sets dFullDEPTHf $1 + +## vvv o dfomnt want to set 2x... +##halcmd setp SEDM.FullDEPTHf $1 +#echo "start 10 sec" +#sleep 10 +#echo "end 10 sec" +#d=$(halcmd setp SEDM.FullDEPTHf $1) +# +## get value setp[d to chceck it +#e=$(halcmd getp SEDM.FullDEPTHf) +#echo "getp rtns $e" # OK +# +## cnvet strg to floast +#fd=$(echo "$e" | bc -l) +#echo "fd is $fd" # OK +# +## vvv XMPL a test of maths on vars +##printf 'fd + fd is= %f\n' "$( bc <<<"$fd + $fd" )" # OK +# +## evaluate fd >0 <0 ==0 +#if (( $(echo "$fd > 0" | bc -l) )); then +# echo "$fd is greater than 0" +#elif (( $(echo "$fd < 0" | bc -l) )); then +# echo "$fd is less than 0" +#else +# echo "$fd is equal to 0" +#fi +#echo "start 10 sec" +#sleep 10 +#echo "end 10 sec" + +# revert to orig, that seems yto work +# querying the comp seems to NOT work +halcmd setp SEDM.FullDEPTHf $1 + +#echo "Rplane dist is $2" + +halcmd setp SEDM.RPlaneDist $2 + + + + +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M163 b/configs/sim/axis/sedm/Mcodes/M163 new file mode 100755 index 00000000000..a9658cf133f --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M163 @@ -0,0 +1,25 @@ +#!/bin/bash + +exec >/dev/null 2>&1 # Redirects all stdout and stderr for the rest of the + +#10.08.2025 M163 + +# usage +# M163 P Q + +#set OrbCut.OrbTypeIN +#set OrbCutWiglRadIN + + +# OrbType is U32 0 circ 1 sqr +# WiglRad is pod Float + +# and Bash rerbs Floaatrs +# so this vvv print trick cnvrts +printf -v OrbTypeInt '%d' "$1" +halcmd sets dOrbitType $OrbTypeInt + +# WiglRad is already a float +halcmd sets dWiglRADf $2 +#echo "WiglRad $2" +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M164 b/configs/sim/axis/sedm/Mcodes/M164 new file mode 100755 index 00000000000..99b8f93b75e --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M164 @@ -0,0 +1,24 @@ +#!/bin/bash + NOT USED thgis not shoyld make using it fail +# User must plug in UNSf belonging to BegNR here +# weell it simpelr gor user to say 1 yes or 0 no +# thna to lookup data so i leave as yes/no QO +# with init of -1 meaning unanswered + + +#24.08.2025 new mcode to set Edm3.PlungeOrbit U32 -1 dwfault 0 dontt so plungeorbit 1 so plungeorbnit +# the -1 value is fefault +# i need to knmow if user has answered "eann orbuit the pklunge cut " or has NOT answered yet +# The comp Edm3 will hang till answered +# Then Edm3 comp will ensure answer is 0 or 1 else abort +# Edm2 comp will abort if value is not -1, 0 or 1 +# +# usage M164 P +# vaalues:s -1 (initial, user has not answered yet +# or 1 (yes wanted ) +# or 0 (not waanted + +printf -v WaantOrbitPlungeInt '%d' "$1" +halcmd sets dPlungeOrbitWanted $WaantOrbitPlungeInt + +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M165 b/configs/sim/axis/sedm/Mcodes/M165 new file mode 100755 index 00000000000..012765a52db --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M165 @@ -0,0 +1,20 @@ +#!/bin/bash + +exec >/dev/null 2>&1 # Redirects all stdout and stderr for the rest of the + +# 03.10.2025 +# M165 P Pitch +# pitch is how many of path are done for 3 FWDS chg i ToolAxis +# 0 means all +# init to -1 so use S32 + + +# usage +# M65 P + +# EtabNum, will become a U32 ( bash always give a f;loat) +# vvv trick to cnvrt Float to INT (U32) +printf -v PitchInt '%d' "$1" +halcmd sets dPitch $PitchInt + +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M166 b/configs/sim/axis/sedm/Mcodes/M166 new file mode 100755 index 00000000000..1b0920c66ab --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M166 @@ -0,0 +1,26 @@ +#!/bin/bash + +exec >/dev/null 2>&1 # Redirects all stdout and stderr for the rest of the + +# 03.10.2025 +# M166 P jumpwanted +# jump is a clockwork peck dtill +# Etrab has suggested CutTimes and JumpDist AJD +# init to 0 +# later allow hdwr swx to control +# swx overridfes etab and M1`66 +printf -v JumpInt '%d' "$1" +halcmd sets dJump $JumpInt + +# 15.02.2026 i has iof [#a = 1] +# chg to use bash -eq +if [ $JumpInt -eq 1 ]; then + halcmd sets dJump True + # Commands to execute if the condition is true +elif [ $JumpInt -eq 0 ]; then + halcmd sets dJump False +else + echo "M166 needs jump = 1 or 0" +fi +# TODO i funno how to exit mauin app when not 0 not 1 +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M190 b/configs/sim/axis/sedm/Mcodes/M190 new file mode 100755 index 00000000000..a08e93572be --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M190 @@ -0,0 +1,13 @@ +#!/bin/bash +# 02.11.2025 M190 tyrns off axis.L.eoffset.enable + +# tComp.ena MUST be IN +#halcmd setp tComp.enaIN False + +halcmd setp axis.x.eoffset-enable False +halcmd setp axis.y.eoffset-enable False +halcmd setp axis.z.eoffset-enable False + +halcmd setp tComp.isEna False + +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M191 b/configs/sim/axis/sedm/Mcodes/M191 new file mode 100755 index 00000000000..e3860790554 --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M191 @@ -0,0 +1,11 @@ +#!/bin/bash +# 02.11.2025 M191 tyrns on axis.L.eoffset.enable + +#halcmd setp tComp.enaIN True +halcmd setp axis.x.eoffset-enable True +halcmd setp axis.y.eoffset-enable True +halcmd setp axis.z.eoffset-enable True + +halcmd setp tComp.isEna True + +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M197 b/configs/sim/axis/sedm/Mcodes/M197 new file mode 100755 index 00000000000..3f6a63efae2 --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M197 @@ -0,0 +1,17 @@ +#!/bin/bash +# M197 no P no Q +# turn of jump if it was left on +# place this in ,ngc just before M02 + +# M197 toggles SEDM.JumpEna +# get checkbnox state +a="$(halcmd getp SEDM.JumpENA)" + +#echo "M197 getp said SEDM.JumpENA was $a " + +if [[ $a == "TRUE" ]]; then + #echo "was TRUE,so toggling " + b="$(halcmd setp techGui.JumpENA.changepin 1)" +fi + +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M198 b/configs/sim/axis/sedm/Mcodes/M198 new file mode 100755 index 00000000000..9ec66b946a9 --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M198 @@ -0,0 +1,12 @@ +#!/bin/bash +# for SEDM suite + +#echo "M198 begin" + +halcmd setp axis.x.eoffset-enable False +halcmd setp axis.y.eoffset-enable False +halcmd setp axis.z.eoffset-enable False + +#echo "M198 end" + +exit 0 diff --git a/configs/sim/axis/sedm/Mcodes/M199 b/configs/sim/axis/sedm/Mcodes/M199 new file mode 100755 index 00000000000..f684e006571 --- /dev/null +++ b/configs/sim/axis/sedm/Mcodes/M199 @@ -0,0 +1,31 @@ +#!/bin/bash +# for SEDM suite + +# 24.10.2025 maybe not necc, could be set in post.hal +# and left set just dont use +# +# M199 +# usage: M199 ( no P Q parms) +# purpose: begin Edm work +# + +#echo "M199 begin" + +halcmd setp axis.x.eoffset-enable True +halcmd setp axis.y.eoffset-enable True +halcmd setp axis.z.eoffset-enable True + +# 12.11.2025 vvv added +halcmd setp SEDM.isEna True + +# 05.02.2026 try to hide pin +#techGui.hiddenU32.forget() +# RESULT: +# ./M199: line 25: syntax error near unexpected token `exit' +# ./M199: line 25: `exit 0' + +# ??? grbg SEDM.RPlaneDist = 00.0 + + +#echo "M199 end" +exit 0 diff --git a/configs/sim/axis/sedm/README b/configs/sim/axis/sedm/README new file mode 100644 index 00000000000..d3ceb92757d --- /dev/null +++ b/configs/sim/axis/sedm/README @@ -0,0 +1,170 @@ +README for comp[ SEDM + +SEDM comp emulates Sink EDM orbiting + +EDM is a machinhing method that removes +microscppic bits of the workpiece +using electrical sparks. + +Sink EDM is the variant used to make molds. +(vs WEDSM for dies and Jole EDM or EDG grinding) +Sink EDM uses shaped tools. +These tools do not rotate. +All the plasic items on your desktop come +from mol;ds that wer EDM'ed. + +Orbiting ius a way to simplify the +manufacture of the shaped tools. + +EDM'ed cavities are larger than the tool +by the length of the spark. The spark +length ( Overburn) is proportional +to the spark's energy +( Currrent * Duration * Dischharge Voltage) +(xmpl 10amps * 10uS * 32Volts) + +Sparks with more energy make larger craters +(rougher surface) +and have larger overburn. +Conversely, sparks with less energy make +shallower craters (smoother surface). + +A molding surface must be smooth +to release the part. + +So the Sink EDM process traditionally used +different sized tools, roughers, +pre-finishers- and finisjers. + +Tools like that are difficukt to make. +Look at an RJ45 connector and image making 3 tools like that form, +one 0.15mm smaller, one 0.100 smaller +and one 0.075 smaller. +All these tool must have the same center. + +Well, Orniting allow the 0.15mm tool do +thhe same work as the smaller ones. +Orgiting remoives the 'many sizes' issue, +by moving the tool in tiny patterns called orbits. + +SEDM comp is mot difficult to use. +The user negins with blueprint/cad drawing +and finds the Fp ( frontal projection + +Get Fp + +of a detail to EDM. +The Fp is the scross sectinal area of the tool +at 'parting line' + +Determine PAARUNG ( Tool and work materials) +In the US and Canada, Graphite is +commonly used for tools, and Steel or Aluminum +for workpiece materials. + +CHOOSE the RTable +Many Etables are provided +Eaxh has a Fp and a Paarung +In thje table, there is a clumn +titled 'RAD'. Then RAD entry +for the 1st line in the Etable is the +UNDERSIZE PER SIDE aka 'UNS' +Make your tool this much smaller. +Aftwr manufacture, measure the tool +to find the MeasuredUNS. +If the MeasuredUNS > UNS, then you +are not finished making the tool. +Go back and grind some more ;-) + +The UNS and ORBITs supllied are 2D, +so only remove lateral stock. +Later I plan on Spherical Orbiting +( a stack of circle) that will require +the UNS applied in 3D. Thats for FUTURE FEATURE. + +Next finbf the cavity depth and refrenev +for that depth. + +Now you have the dimensions, positiins, +UNS, Etable and can begin progtramming. +Most NGC EDM code is finng in Mcode P's & Q's. + +NB: Orbits are TINY motions, +so zoom WAY in! To see beteer, +do not show Tool, avoid perspective view. + +NB The motion may zeem unevne. It IS uneven. +The progress alomg a perdetermioned path is +comtrolled by a random generator that moves +FWD HOLD or BWD along the path. If Bwd occurs, there will be a +DETOUR gnerated to move the tool away from stock. +Aee the X view of the demo below and observe the +'fringe' on the square path. Those ar 'detours'. +Tirn the JUMP on and off, using the checkbox. +Try The PEEK button and when the tool returns to +its starting position, try RESUME or WUIT. + + + +control signal is moving FWD or HOLD or Bed thru a predetermined path. +controls signal is moving Fwd abd Bwd +example + +;XMPLE.ngc cuts Z negative -1.204mm deerp +; DATUN for cut X1.0 Y 0 Z1.0 +; ORBIT type SQUARE +; ETABLE 34.ENC (This just finishing a cavity) +; ETABLE BegNR 17 EndNR 15 +; MsrdUNS == Etable UNS +o200 sub + M66 E0 L0 ;NEED QUEIE BUSTER so motion is stopped + M199 ; This begins EDM control + M162 P-1.304 Q+1.00 ; awt PrintDepth and Rplanemore tests per hr lookimg fdor bad tri from peri tto SPO + M163 P1 Q0 ; OrbType SQR, no 'Wigl' for bore + M160 P34 Q0.254 ; Etable, MsrdUNS + M161 P17 Q15 ; BeginningNR in Etable, EndNR + M00 ; needed for ExternalOffsets + M198 ; Rnd SEDM control + ; thsi last line wont be executed + ; untill AEDM comp finisshes +o200 endsub ; return to NGC code and LCNC position control +;now thw main NGC progtram poses the tool. and calls the o-sub. +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; posing can be rapid +G10L2P1 X0 Y0 Z0 ;'UNSHIFT' +; +#1 = 0 ;counter initial value +#2 = 1 ;counte max value +#3 = +2.000 ; Cplane above clamping/fixtires +#4 = +1.0 ; Rplane above woek wher EDM Power is turned on +; +o110 while [#1 LT #2] + g10l2p1 x0 y0 z0 ; UNSHIFT + G0Z5 ; mNUl tool chg for ToolAxis + ;//////////////////// DATUN for cut + g10l2p1 x1 y 0 z1 ;DATUM ref [posn + g0z#3 ;Cplane rek to Datum + g0 x0 y0 ;cavity center + z#4 ;RPlane rel to DATUM at G53 2.5 now + ;//////////////////// Cut + o200 call + ;//////////////////// + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3 ;Cplane rel toDATUM + ; + #1 = [#1 + 1] ;bump ctr, Useful for usinga Positionn list +o110 endwhile +;//////////////////// goto exit posn, adjust fdor G17.18/19 and CutDirection +G10L2P1X0Y0Z0 ;UNHIFT +G0Z5 ;manual Tool Chg height and tool axis +G0X0Y0 ;manual Tool Vhg posn for 'other' axis alreaady at Cplane, moce to convenient x y +;//////////////////// end pgm +M197 ;T turn off JumpENA if leaft on +M02 +% + diff --git a/configs/sim/axis/sedm/SEDM.hal b/configs/sim/axis/sedm/SEDM.hal new file mode 100644 index 00000000000..18f93840933 --- /dev/null +++ b/configs/sim/axis/sedm/SEDM.hal @@ -0,0 +1,202 @@ +# SEDM.hal 30.09.2025 +# +#07.01.2026 DD Bae tghrwAA TO TRY CAPTIRE UNWNATED JUMPS TO spo +# +#28.10.2025 author used a cale and renamed it +# this cuased helll when i wnated to afdd 3 scales +# becuz his qwoukld never be dounf searchinf for scale.0/1/2... +# so i renamed his singlke to scale.,4, +# xhgf the addf for all 4 +# +# +# user space components +loadusr -W hal_manualtoolchange + +# components +loadrt trivkins coordinates=XYZ +# 07.01.2026 ALLOW BASR PD TP CATCH JUMP +# i dont see any addf to nbase_thread +# i think i added base_thread afster tan servo +# while tryuing tro trap tall skimnmy triangles problem + +loadrt motmod base_period_nsec=0 servo_period_nsec=1000000 num_joints=3 +# 05.02.2026 vvv trouble w unexpeted realtime errors MAYBE hurting s.poll for jump +#loadrt motmod base_period_nsec=50000 servo_period_nsec=1000000 num_joints=3 +loadrt pid names=J0_pid,J1_pid,J2_pid + +loadrt mux2 names=J0_mux,J1_mux,J2_mux +loadrt ddt names=J0_vel,J0_accel,J1_vel,J1_accel,J2_vel,J2_accel +loadrt hypot names=hyp_xy,hyp_xyz + +loadrt sim_home_switch names=J0_switch,J1_switch,J2_switch +loadrt sim_spindle names=sim_spindle +loadrt limit2 names=limit_speed +loadrt lowpass names=spindle_mass +loadrt near names=near_speed +loadrt scale count=4 +#names=rpm_rps + +# pin aliases +# param aliases +# signals +# nets + +# goddamn J: crap he grouped jopint items using this goofy prefic + +net J0:acc J0_accel.out +net J0:enable joint.0.amp-enable-out => J0_pid.enable +net J0:homesw J0_switch.home-sw => joint.0.home-sw-in +net J0:on-pos J0_pid.output => J0_mux.in1 +net J0:pos-cmd joint.0.motor-pos-cmd => J0_pid.command +net J0:pos-fb J0_mux.out => J0_mux.in0 J0_switch.cur-pos J0_vel.in joint.0.motor-pos-fb +net J0:vel J0_vel.out => J0_accel.in hyp_xy.in0 hyp_xyz.in0 + +net J1:acc J1_accel.out +net J1:enable joint.1.amp-enable-out => J1_pid.enable +net J1:homesw J1_switch.home-sw => joint.1.home-sw-in +net J1:on-pos J1_pid.output => J1_mux.in1 +net J1:pos-cmd joint.1.motor-pos-cmd => J1_pid.command +net J1:pos-fb J1_mux.out => J1_mux.in0 J1_switch.cur-pos J1_vel.in joint.1.motor-pos-fb +net J1:vel J1_vel.out => J1_accel.in hyp_xy.in1 hyp_xyz.in1 + +net J2:acc J2_accel.out +net J2:enable joint.2.amp-enable-out => J2_pid.enable +net J2:homesw J2_switch.home-sw => joint.2.home-sw-in +net J2:on-pos J2_pid.output => J2_mux.in1 +net J2:pos-cmd joint.2.motor-pos-cmd => J2_pid.command +net J2:pos-fb J2_mux.out => J2_mux.in0 J2_switch.cur-pos J2_vel.in joint.2.motor-pos-fb +net J2:vel J2_vel.out => J2_accel.in hyp_xyz.in2 + +net estop:loop iocontrol.0.user-enable-out => iocontrol.0.emc-enable-in + +net sample:enable motion.motion-enabled => J0_mux.sel J1_mux.sel J2_mux.sel + +net spindle-at-speed near_speed.out => spindle.0.at-speed +net spindle-index-enable sim_spindle.index-enable <=> spindle.0.index-enable +net spindle-orient spindle.0.orient => spindle.0.is-oriented +net spindle-pos sim_spindle.position-fb => spindle.0.revs +#net spindle-rpm-filtered spindle_mass.out => near_speed.in2 rpm_rps.in +net spindle-rpm-filtered spindle_mass.out => near_speed.in2 scale.3.in + +#net spindle-rps-filtered rpm_rps.out => spindle.0.speed-in +net spindle-rps-filtered scale.3.out => spindle.0.speed-in + +net spindle-speed-cmd spindle.0.speed-out => limit_speed.in near_speed.in1 +net spindle-speed-limited limit_speed.out => sim_spindle.velocity-cmd spindle_mass.in + +net tool:change iocontrol.0.tool-change => hal_manualtoolchange.change +net tool:changed hal_manualtoolchange.changed => iocontrol.0.tool-changed +net tool:prep-loop iocontrol.0.tool-prepare => iocontrol.0.tool-prepared +net tool:prep-number iocontrol.0.tool-prep-number => hal_manualtoolchange.number + +net xy:vel hyp_xy.out +net xyz:vel hyp_xyz.out + +# parameter values +setp J0_accel.tmax 0 +setp J0_mux.tmax 0 +setp J0_pid.do-pid-calcs.tmax 0 +setp J0_switch.tmax 0 +setp J0_vel.tmax 0 + +setp J1_accel.tmax 0 +setp J1_mux.tmax 0 +setp J1_pid.do-pid-calcs.tmax 0 +setp J1_switch.tmax 0 +setp J1_vel.tmax 0 + +setp J2_accel.tmax 0 +setp J2_mux.tmax 0 +setp J2_pid.do-pid-calcs.tmax 0 +setp J2_switch.tmax 0 +setp J2_vel.tmax 0 + +setp hyp_xy.tmax 0 +setp hyp_xyz.tmax 0 + +setp limit_speed.tmax 0 + +setp motion-command-handler.tmax 0 +setp motion-controller.tmax 0 + +setp near_speed.difference 10 +setp near_speed.scale 1.1 +setp near_speed.tmax 0 + +#setp rpm_rps.tmax 0 +setp scale.3.tmax 0 + + +setp servo-thread.tmax 0 + +setp sim_spindle.scale 0.01666667 +setp sim_spindle.tmax 0 +setp spindle_mass.gain 0.07 +setp spindle_mass.tmax 0 + + + +# realtime thread/function links +addf motion-command-handler servo-thread +addf motion-controller servo-thread + +addf J0_pid.do-pid-calcs servo-thread +addf J1_pid.do-pid-calcs servo-thread +addf J2_pid.do-pid-calcs servo-thread +addf J0_mux servo-thread +addf J1_mux servo-thread +addf J2_mux servo-thread +addf J0_vel servo-thread +addf J0_accel servo-thread +addf J1_vel servo-thread +addf J1_accel servo-thread +addf J2_vel servo-thread +addf J2_accel servo-thread +addf hyp_xy servo-thread +addf hyp_xyz servo-thread +addf J0_switch servo-thread +addf J1_switch servo-thread +addf J2_switch servo-thread +addf limit_speed servo-thread +addf spindle_mass servo-thread + +#addf rpm_rps servo-thread +addf scale.0 servo-thread +addf scale.1 servo-thread +addf scale.2 servo-thread +addf scale.3 servo-thread + +addf near_speed servo-thread +addf sim_spindle servo-thread + +# setp commands for unconnected input pins +setp J0_pid.FF0 1.0 +setp J0_pid.Pgain 0 +setp J0_pid.Dgain 0 +setp J0_pid.Igain 0 +setp J0_pid.FF1 0 +setp J0_pid.FF2 0 +setp J1_pid.FF0 1.0 +setp J1_pid.Pgain 0 +setp J1_pid.Dgain 0 +setp J1_pid.Igain 0 +setp J1_pid.FF1 0 +setp J1_pid.FF2 0 +setp J2_pid.FF0 1.0 +setp J2_pid.Pgain 0 +setp J2_pid.Dgain 0 +setp J2_pid.Igain 0 +setp J2_pid.FF1 0 +setp J2_pid.FF2 0 + +setp sim_spindle.scale 0.01666667 +setp limit_speed.maxv 5000.0 +setp spindle_mass.gain .07 +setp near_speed.scale 1.1 +setp near_speed.difference 10 + +#/// old pin settung +#setp axis.x.eoffset-scale 0.001 +#setp axis.y.eoffset-scale 0.001 +#setp axis..eoffset-scale 0.001 +#/// diff --git a/configs/sim/axis/sedm/SEDM.ini b/configs/sim/axis/sedm/SEDM.ini new file mode 100644 index 00000000000..88e76cd2c89 --- /dev/null +++ b/configs/sim/axis/sedm/SEDM.ini @@ -0,0 +1,206 @@ +# 29.12.2025 mk default ngv 1wiglZneg,ngc + +# 03.11.2025 note @ S/V ratio +# [AXIS_Z] +# # Note: low OFFSET_AV_RATIO: +# +# #03.11.2025 saw 0.5 in dunamiv_offsets cfg +# # with note saying "give 1.2 to excternal offsets +# # [AXIS_Z] +# # Note:give half to external_offsets: +# # OFFSET_AV_RATIO = 0.5 +# # +# # 03.11.2025 u used 0.9 anf git hyge speen inscrease +# # but shoudl try 0.5 not right now +# OFFSET_AV_RATIO = 0.9 +# +# +# 08.10.2025 ng at stooping pt , not at same posn +# abd Axis path trace is a SQIGGLE THAT TURNS THEMN HEADS STARIHHT FOWN +# SO +# i did lots of testing of cL and StairsL +# to make sure they always mades same data given random inours +# # result: ok w randowm inouts, two passes at mkcL and mkStairsl +# wew like test1 andtest2 +# for 100 rndom inpts, test1 == test 2 +# +# so end posn us ng and varting +# but cL and StairsL are proven ok +# +# so err is after StairsL created, +# likely in doStairs or lower doEdmStep +# +# freeze this +# crippler doStairs to only [rint each step and compare new posn to StairsL[ndx] +# +# test b4 freexe ends at -0.002 0.000 -0.004 +# last elem in StairsL is (5, -1, -49) +# 2nd try +# ends w DRO at -0.002 -0.001 -0.006 +# last elem in StairsL is (5, -1, -49) +# same input , digg result !!! bbad computer , bbad!! + + +# 06.10.2025 depth is ng +# i say startposn is 0,0,+/010 +# i say FD is --.264 +# etab uns is 2.794 +# so UNS =2.794-2.54 = .254 +# rufpt is FD - UNS ??? MsrdUNS ??? +# -.264 - .254 HERE HERE HERE asleep + +# SEDM.ini 06.10.2025 +# the suite now moves all 3 axis +# i only had z motion +# becuz i didnt cfg OFFSET_AV_RATIO = 0.05 for X Y +# now freexe this suite, clean up, uncripplt.... +# +[HAL] +HALFILE = SEDM.hal +# use no post gui for ear;y tests +POSTGUI_HALFILE = SEDMpost.hal +HALUI = halui + +[EMC] +MACHINE = SEDM +# vvv bewares of nagging upddate dlog due top chging thiusvvv +VERSION = 1.1 +#DEBUG = 0x00000003 + +[DISPLAY] +DISPLAY = axis +POSITION_OFFSET = RELATIVE +POSITION_FEEDBACK = ACTUAL +MAX_LINEAR_VELOCITY = 2 +# try load NO mgc OPEN_FILE = ./SEDM06.ngc +# in attempot to stop SEDM comp form dissappearing +# no luck, AWSN ias no oin hal cfg flog +# techGui and updown ecist and can be setpd etc +# but not SEDM not in comp or pun list of hal cfg dlog +# didnt happen vvv +#OPEN_FILE = /home/cnc/Downloads/aSEDM-06102025woorking/SEDM06.ngc +# &&&& ok + +# vvv see dfiff between NOPGM and HASPGM +# before F1 F2 homeall +# w/o PGM ,SEDM was alive with deadstop after while EDMmode == True: +# with PGM SEDM pins all there B4 F1 F2 homeall +# and after F1 F3 homeall SEDM OK all pins +#OPEN_FILE = "" +# vvv 07 has queue busters +#OPEN_FILE = ./SEDMmultDStraight3.ngc +OPEN_FILE = ./ngc/1orb/nuZnegWiglNR17-15.ngc + +# was SEDMmult07.ngc + + +# ./SEDM06.ngc +# no quotes in google xmpl + + + +#OPEN_FILE = "./ferf6.ngc" # got no error + +# Introductory graphic +INTRO_GRAPHIC = linuxcnc.gif +INTRO_TIME = 1 + +[TASK] +TASK = milltask +CYCLE_TIME = 0.001 + +[RS274NGC] +USER_M_PATH = ./Mcodes/ +PARAMETER_FILE = sim.var + +[EMCIO] +EMCIO = io +CYCLE_TIME = 0.100 +TOOL_TABLE = SEDM.tbl + +[EMCMOT] +EMCMOT = motmod +# i think i need a base period for conv_dloast_s32 +# 03.09.2025 i dont use any conv +#07.01.2026 allow base thread just to captur 'jump' unwanted luch peri to SPO +BASE_PERIOD = 50000 +SERVO_PERIOD = 1000000 + +[TRAJ] +COORDINATES = XYZ +LINEAR_UNITS = mm +ANGULAR_UNITS = degree + +[KINS] +JOINTS = 3 +KINEMATICS = trivkins coordinates=XYZ + +# 06.10.2025 no fn clude what AV ratio us but Z had irt and CY not, and CY no move so make same +# SONOFABITCH!!!! NOW X and Y MOVE under edm gv ctrl +# feom lcnc ggogle Default value: 0 (disables external offset). +# +[AXIS_X] +# Note: low OFFSET_AV_RATIO: +#OFFSET_AV_RATIO = 0.05 +# 0/9 is max allowed +OFFSET_AV_RATIO = 0.9 +MIN_LIMIT = -150 +MAX_LIMIT = 150 +#MAX_VELOCITY = 2 +#MAX_ACCELERATION = 20 +MAX_VELOCITY = 20 +MAX_ACCELERATION = 200 + +[AXIS_Y] +# Note: low OFFSET_AV_RATIO: +#OFFSET_AV_RATIO = 0.05 +OFFSET_AV_RATIO = 0.9 +MIN_LIMIT = -150 +MAX_LIMIT = 150 +#MAX_VELOCITY = 2 +#MAX_ACCELERATION = 20 +MAX_VELOCITY = 20 +MAX_ACCELERATION = 200 + +[AXIS_Z] +# Note: low OFFSET_AV_RATIO: + +#03.11.2025 saw 0.5 in dunamiv_offsets cfg +# with note saying "give 1.2 to excternal offsets +# [AXIS_Z] +# # Note:give half to external_offsets: +# OFFSET_AV_RATIO = 0.5 +# +# 03.11.2025 u used 0.9 anf git hyge speen inscrease +# but shoudl try 0.5 not right now +OFFSET_AV_RATIO = 0.9 +MIN_LIMIT = -150 +MAX_LIMIT = 150 +#MAX_VELOCITY = 2 +#MAX_ACCELERATION = 20 +MAX_VELOCITY = 20 +MAX_ACCELERATION = 200 + +[JOINT_0] +TYPE = LINEAR +HOME_SEQUENCE = 0 +#MAX_VELOCITY = 2 +#MAX_ACCELERATION = 20 +MAX_VELOCITY = 20 +MAX_ACCELERATION = 200 + +[JOINT_1] +TYPE = LINEAR +HOME_SEQUENCE = 0 +#MAX_VELOCITY = 2 +#MAX_ACCELERATION = 20 +MAX_VELOCITY = 20 +MAX_ACCELERATION = 200 + +[JOINT_2] +TYPE = LINEAR +HOME_SEQUENCE = 0 +#MAX_VELOCITY = 2 +#MAX_ACCELERATION = 20 +MAX_VELOCITY = 20 +MAX_ACCELERATION = 200 diff --git a/configs/sim/axis/sedm/SEDM.tbl b/configs/sim/axis/sedm/SEDM.tbl new file mode 100644 index 00000000000..3a5209c2c34 --- /dev/null +++ b/configs/sim/axis/sedm/SEDM.tbl @@ -0,0 +1,2 @@ +T1 P1 Z0.5 D0.125 +T2 P2 Z2 D0.125 diff --git a/configs/sim/axis/sedm/SEDM.xml b/configs/sim/axis/sedm/SEDM.xml new file mode 100644 index 00000000000..e26d4410b80 --- /dev/null +++ b/configs/sim/axis/sedm/SEDM.xml @@ -0,0 +1,315 @@ + + + + + + + + + + + + "EtabNum" + ("DejaVu Sans Mono",18,"bold") + "8d" + 8 + "red" + + + + + "UNS" + ("DejaVu Sans Mono",12,"bold") + "LightBlue3" + "2.3f" + + + + + "ThisRAD" + ("DejaVu Sans Mono",12,"bold") + "LightBlue3" + "2.3f" + + + + + ("DejaVu Sans Mono",12,"bold") + + + + + + + + + + + + + + + "NR" + "2d" + "LightBlue3" + ("DejaVu Sans Mono",12,"bold") + 2 + + + "IP" + "3d" + ("DejaVu Sans Mono",12,"bold") + 3 + + + "P" + "1d" + "LightBlue3" + ("DejaVu Sans Mono",12,"bold") + 1 + + + "HV" + "1d" + 3 + ("DejaVu Sans Mono",12,"bold") + + + "TON" + "4d" + "LightBlue3" + ("DejaVu Sans Mono",12,"bold") + 4 + + + "ISO" + "1d" + ("DejaVu Sans Mono",12,"bold") + 3 + + + "BWDmax" + "2d" + ("DejaVu Sans Mono",12,"bold") + "LightBlue3" + 3 + + + "RAD" + "1.3f" + ("DejaVu Sans Mono",12,"bold") + 5 + + + "SPA" + "1.0f" + ("DejaVu Sans Mono",12,"bold") + "LightBlue3" + 5 + + + "VDI" + "3d" + ("DejaVu Sans Mono",12,"bold") + 3 + +
+ + + + ("DejaVu Sans Mono",12,"bold") + + + ("DejaVu Sans Mono",12,"bold") + + + + + "right" + "TOF" + 1 + 9999 + 0000 + 1.0 + "4.0f" + ("DejaVu Sans Mono",12,"bold") + 1 + 7 + + + + + + ("DejaVu Sans Mono",12,"bold") + + + + + "GVHI" + 0 + 100 + 0000 + 1 + "3f" + ("DejaVu Sans Mono",12,"bold") + 1 + 4 + + + + + + "GVLO" + 0 + 100 + 0000 + 1 + "3f" + ("DejaVu Sans Mono",12,"bold") + 1 + 4 + + + + + + ("DejaVu Sans Mono",12,"bold") + + + + + "JumpENA" + + + 0 + 1 + + 1 + + + + + + + + + + + + + + "ET" + 0.001 + 10.0 + 0000 + 0.001 + "1.3f" + ("DejaVu Sans Mono",12,"bold") + 1 + 6 + + + + + + "AJD" + 0.010 + 10.0 + 0000 + 0.01 + "1.2f" + ("DejaVu Sans Mono",12,"bold") + 1 + 6 + + + + + + + + + + + diff --git a/configs/sim/axis/sedm/SEDMpause.xml b/configs/sim/axis/sedm/SEDMpause.xml new file mode 100644 index 00000000000..5fee76a7236 --- /dev/null +++ b/configs/sim/axis/sedm/SEDMpause.xml @@ -0,0 +1,41 @@ + + + + + + + + + + + + + + + + + diff --git a/configs/sim/axis/sedm/SEDMpost.hal b/configs/sim/axis/sedm/SEDMpost.hal new file mode 100644 index 00000000000..8a00813bbf3 --- /dev/null +++ b/configs/sim/axis/sedm/SEDMpost.hal @@ -0,0 +1,126 @@ +# SEDMpost.hal 30.09.2025 +# 02.02.2026 TODO need dummy genetatyoe comp 'gen' +# just rcvs gen inmfo untyil real gen buiult +# +# 11.12.2025 the SEDMctr cant be cleared not writeavle +# +#==============beg loads=============== + +loadusr -Wn techGui pyvcp -c techGui ./SEDM.xml +loadusr -Wn EDpanel pyvcp -g 200x150+800+50 -c EDpanel ./SEDMpause.xml +loadusr -W SEDM + +#==============end loads=============== + +net inpo motion.in-position SEDM.inpo + +net J0:pos-fb SEDM.xFBf +net J1:pos-fb SEDM.yFBf +net J2:pos-fb SEDM.zFBf + +#net sABORT => halui.abort + +setp SEDM.xyzSCALEfIN 0.001 + +net stepSize SEDM.xyzSCALEfOUT axis.x.eoffset-scale +net stepSize axis.y.eoffset-scale +net stepSize axis.z.eoffset-scale + +# cnx non editable parms im SEDM to techGUI and generator +net dNR SEDM.NR techGui.NR #gen.NR #U32 +net dIP SEDM.IP techGui.IP #gen.IP #u32 +net dHV SEDM.HV techGui.HV #gen.HV #U32 + +net dTON SEDM.TON techGui.TON #gen.TONO #FLOAT + +net dP SEDM.P techGui.P # gen.IP +net dISO SEDM.ISO techGui.ISO # gen/ISO + +#01.02.2026 try set spinbox initial value to etab value +net sTOFetab SEDM.TOF techGui.spinbox.0.param_pin +net sGVHIetab SEDM.GVHI techGui.spinbox.1.param_pin +net sGVLOetab SEDM.GVLO techGui.spinbox.2.param_pin +net sETetab SEDM.ET techGui.spinbox.3.param_pin +net sAHDetab SEDM.AJD techGui.spinbox.4.param_pin + +#02.02.2026 set generator with spinbox value +net sTOFout techGui.TOF #gen.TOF +net sGVHIout techGui.GVHI #gen.GVHI +net sGVLOout techGui.GVLO #gen.GVLO +net sETout techGui.ET #gen.ET +net sAJDout techGui.AJD #gen.AJD + +net sJumpENA techGui.JumpENA SEDM.JumpENA +#02.02.2026 after a progtram is done +# if SEDM.JumpENA == True: +# #turn iot off before next use +# SEDM.ChgJumpENA = 0 +#03.02.2026 unlink these 2 +# domt use a net , dfo manually +# net sChgJumpENA SEDM.ChgJumpENA techGui.JumpENA.changepin + +# set other etab values direct to generator +#///// +# TODO 02.02.2026 i tyhink gen shoulf be src for genready +# h.newpin("GenReady", hal.HAL_S32, hal.HAL_IN) +# #??? really??? was it but code cant set that DOUT) +#///// + +net dBWDmax SEDM.BWDmax techGui.BWDmax + +# 31.01.2026 removed net dVE SEDM.VEf techGui.Ve +# 31.01.2026 removed net dVw SEDM.VWf techGui.Vw +net dVDI SEDM.VDIf techGui.VDI + +net dRAD SEDM.RADf techGui.RAD +net dSPA SEDM.SPAf techGui.SPA + +net dOrbitType SEDM.OrbitType +net dWiglRADf SEDM.WiglRADf +net dPlungeOrbitWanted SEDM.PlungeOrbitWanted + +net dPitch SEDM.Pitch + +net dUNS SEDM.UNSf techGui.UNS +net dThisRad SEDM.ThisRADf techGui.ThisRAD + +net dEtabNum SEDM.EtabNum techGui.EtabNum + +# 04.02.2026 no more techGui BegNR EndNR + +net eox SEDM.XOffsetCmd axis.x.eoffset-counts +net eoy SEDM.YOffsetCmd axis.y.eoffset-counts +net eoz SEDM.ZOffsetCmd axis.z.eoffset-counts + +#15.02.2026 not used setp SEDM.PulseCount 0 +setp SEDM.freebies 20 #12 + +net die SEDM.abort halui.abort + +# 02.02.2026 TODO need trhhisvvv??? i got disableOsc +net hot SEDM.disableOsc EDpanel.EDpeek.disable + +# make sure SEDM.isNotCutting is True asap after start + +net EDpk EDpanel.EDpeek SEDM.EDpeek +net EDret EDpanel.EDreturn SEDM.EDreturn +net EDq EDpanel.EDquit SEDM.EDquit + +net dMsrdUNSf SEDM.MsrdUNSf + +net ForzFWD SEDM.ForceFWD EDpanel.ForzFWD +net ForzHOLD SEDM.ForceHOLD EDpanel.ForzHOLD +net ForzBWD SEDM.ForceBWD EDpanel.ForzBWD + +net inpo motion.in-position SEDM.inpo + +#loadusr halmeter -g 800 10 pin SEDM.JumpENA +#loadusr halmeter -g 800 210 pin SEDM.endJT +#loadusr halmeter -g 800 410 pin SEDM.JumpOn +#loadusr halmeter -g 800 610 pin SEDM.AJD + + +# vvv not writeable tyep HAL_IN +# awtting up initl state is a prob to be solved +#setp SEDM.DontEnaPeek True NOT WRITREABLE +#setp SEDM.DisableRetQuit True NOT WRITREABLE diff --git a/configs/sim/axis/sedm/ngc/16x/16xZnegNoWiglNR15-15.ngc b/configs/sim/axis/sedm/ngc/16x/16xZnegNoWiglNR15-15.ngc new file mode 100644 index 00000000000..f13914b362f --- /dev/null +++ b/configs/sim/axis/sedm/ngc/16x/16xZnegNoWiglNR15-15.ngc @@ -0,0 +1,208 @@ +;SEDMmulDstraight3.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.0 ; FD RPlabe + M163 P0 Q0.0; OrbType Circle, EiglRad 50um + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P15 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y0 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y0 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y0 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y2 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y2 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y2 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y2 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x10 y4 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y4 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y4 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y4 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y6 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y6 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y6 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y6 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/16x/16xZnegWiglNR25-15.ngc b/configs/sim/axis/sedm/ngc/16x/16xZnegWiglNR25-15.ngc new file mode 100644 index 00000000000..b063f686e49 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/16x/16xZnegWiglNR25-15.ngc @@ -0,0 +1,208 @@ +;SEDMmulDstraight3.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.0 ; FD RPlabe + M163 P1 Q0.010; OrbType SQR, WiglRad 50um + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y0 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y0 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y0 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y2 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y2 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y2 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y2 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x10 y4 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y4 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y4 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y4 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y6 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y6 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y6 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y6 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/16x/16xZnegWiglNR25-24.ngc b/configs/sim/axis/sedm/ngc/16x/16xZnegWiglNR25-24.ngc new file mode 100644 index 00000000000..3af2dbe4e31 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/16x/16xZnegWiglNR25-24.ngc @@ -0,0 +1,208 @@ +;SEDMmulDstraight3.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.0 ; FD RPlabe + M163 P0 Q0.005; OrbType Circle, EiglRad 50um + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q24 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y0 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y0 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y0 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y2 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y2 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y2 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y2 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x10 y4 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y4 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y4 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y4 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y6 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y6 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y6 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y6 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/16x/16xZnegWiglNR25-25.ngc b/configs/sim/axis/sedm/ngc/16x/16xZnegWiglNR25-25.ngc new file mode 100644 index 00000000000..00e81ed5f86 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/16x/16xZnegWiglNR25-25.ngc @@ -0,0 +1,208 @@ +;SEDMmulDstraight3.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.0 ; FD RPlabe + M163 P0 Q0.05; OrbType Circle, EiglRad 50um + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y0 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y0 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y0 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y2 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y2 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y2 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y2 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x10 y4 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y4 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y4 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y4 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y6 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y6 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y6 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y6 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/16x/1firstOrb.ngc b/configs/sim/axis/sedm/ngc/16x/1firstOrb.ngc new file mode 100644 index 00000000000..27677c09ddf --- /dev/null +++ b/configs/sim/axis/sedm/ngc/16x/1firstOrb.ngc @@ -0,0 +1,157 @@ +;1rowEachType.ngc +; +; thinks its at SPO +; BEFORE calle to doCtrSpo +; +; single row with 1 cut of each type +; just wigl +; jist 1st orb +; just last orb +; wigl and all robs +; +; there some left over nad thing +; so swap the order of types to see and test +; +; 1st err, when allorbs follow justlast, the 1st move seems to be +; fro ryfpt to startpt +; the line is curved and quick +; +; test1: sub call order is 210 220 230 240 +; make same Z datum +; +; res: i see LastOrb posn hozz fro RufPtTipl +; tyo get to AllOrbs cut +; so LastOrb needs rtn to DPO b4 exit +; why doesnt 1stOrb show similar??? +; sunno +; do g10l2p1x0y0z0 AND rehome befoore xit LCNC and wacth again +; esp watch 1stOrb to LastOrb motion +; 1stOrb motion to LastOrb is correct +; motion LastOrb to AllOrb is ng +; +o210 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.000 ; FD RPlane + + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + M160 P34 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q25 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o210 endsub + +o220 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.000 ; FD RPlane + M163 P0 Q0.0 ; OrbType Circle, WiglRad 50um5 + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q24 ; BegNR EndNR + M00 + M198 +o220 endsub + +o230 sub + ; just last orb + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + + M163 P0 Q0.0 ; OrbType Circle, EiglRad 50um + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P15 Q15 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o230 endsub +;end just last orb + +o240 sub + ; wigl and all orbits + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + + M163 P1 Q0.012 ; OrbType Circle, EiglRad 50um + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q15 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o240 endsub +;end wigl and all orbits + +; /////////////// end subs //////// +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 10(limit) +#3 = +5.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0 ; UNSHIFT + G0Z#3 ; CPlane + + ;;-DETAIL 1 ------------- + ;g10l2p1 x10 y0 z-2 ;DATUM 1 + ;g0x0y0 + ;z#4 ;RPlane rel to DATUM + ;o210 call + ;g10l2p1 x0 y0 z0 ;UNSHIFT + ;G0Z#3 ;CPlane abso mc coords + + ;-DETAIL 2------------------------- + ;g10l2p1 x12 y0 z-2 ; DATUM 2 + ;g0x0y0 ; rapid to DATUM 2 ctr + ;z#4 ; rapid to RPlane + ;o220 call ; cut Detail 2 + ;g10l2p1x0y0z0 ; UNSHIFT + ;G0Z#3 + + ;g10l2p1 x14 y0 z-2 ; Set DATUM 3 + ;g0x0y0 ; rapid to DATUM 3 ctr + ;z#4 + ;o230 call ; cut dertail 3 + ;g10l2p1x0y0z0 ;UNSHIFT + ;G0Z#3 + + g10l2p1 x16 y0 z-2 ; set DATUM 4 + g0x0y0 + z#4 + o240 call ; cut detail 4 + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 ;UNSHIFT +G0Z#3 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/16x/1rowEachType.ngc b/configs/sim/axis/sedm/ngc/16x/1rowEachType.ngc new file mode 100644 index 00000000000..bd37dc6386d --- /dev/null +++ b/configs/sim/axis/sedm/ngc/16x/1rowEachType.ngc @@ -0,0 +1,135 @@ +;1rowEachType.ngc +; +; +o210 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.000 ; FD RPlane + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 ; BegNR EndNR + M00 + M198 +o210 endsub + +o220 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.000 ; FD RPlane + + M163 P0 Q0.0 ; OrbType Circle, WiglRad 50um5 + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q24 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o220 endsub + +o230 sub + ; just last orb + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + + M163 P0 Q0.0 ; OrbType Circle, EiglRad 50um + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P15 Q15 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o230 endsub +;end just last orb + +o240 sub + ; wigl and all orbits + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + + M163 P1 Q0.012 ; OrbType Circle, EiglRad 50um + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q15 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o240 endsub +;end wigl and all orbits + +; /////////////// end subs //////// +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +T2 +M6 + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 10 (limit) +#3 = +5.000 ; CPlane +#4 = +1.000 ; RPlane + +#5 = 0 ; yaxis + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0 ; UNSHIFT + G0Z#3 ; CPlane + + ;-DETAIL 1 ------------- + g10l2p1 x10 y#5 z-2 ;DATUM 1 + g0x0y0 + z#4 ;RPlane rel to DATUM + o210 call + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3 ;CPlane abso mc coords + + ;-DETAIL 2------------------------- + g10l2p1 x12 y#5 z-2 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + o220 call ; cut Detail 2 + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + ;-Detail 3 + g10l2p1 x14 y#5 z-2 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + o230 call ; cut dertail 3 + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y#5 z-2 ; set DATUM 4 + g0x0y0 + z#4 + o240 call ; cut detail 4 + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + #1 = [#1 + 1] + #5 = [#5 + 2] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 ;UNSHIFT +G0Z#3 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/16x/2eachWigl-25-15-all.ngc b/configs/sim/axis/sedm/ngc/16x/2eachWigl-25-15-all.ngc new file mode 100644 index 00000000000..9967c0c02c6 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/16x/2eachWigl-25-15-all.ngc @@ -0,0 +1,261 @@ +;SEDMmulDstraight3.ngc +; wigl and all orbs seems to begin at RufPtTul, +; jump (xcurved) to top +; then runs ~ok +; mnove it to from row by swappinsg sib name/numbet +; +; +o240 sub + ; just wigl + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + M163 P0 Q0.05 ; OrbType Circle, EiglRad 50um + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 ; BegNR EndNR + M00 + M198 +o240 endsub +;end just wigl + +o220 sub + ; just first orb + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + M163 P0 Q0.0 ; OrbType Circle, EiglRad 50um + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q24 ; BegNR EndNR + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o220 endsub +;end just first orb + +o230 sub + ; just last orb + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + M163 P0 Q0.0 ; OrbType Circle, EiglRad 50um + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P15 Q15 ; BegNR EndNR + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o230 endsub +;end just last orb + +o210 sub + ; wigl and all orbits + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + M163 P0 Q0.025 ; OrbType Circle, EiglRad 50um + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q15 ; BegNR EndNR + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o210 endsub +;end wigl and all orbits + +; /////////////// end subs //////// +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o210 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y0 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o210 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y0 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o210 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y0 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o210 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y2 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o220 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y2 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o220 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y2 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o220 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y2 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o220 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x10 y4 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o230 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y4 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o230 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x14 y4 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o230 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y4 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o230 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + ;//////////////////// Posn 1 + g10l2p1 x16 y6 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o240 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x14 y6 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o240 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1 x12 y6 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + ;//////////////////// + o240 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x10 y6 z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o240 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/XnegWiglNR17-15.ngc b/configs/sim/axis/sedm/ngc/1orb/XnegWiglNR17-15.ngc new file mode 100644 index 00000000000..57395f08cff --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/XnegWiglNR17-15.ngc @@ -0,0 +1,67 @@ +;XnegsWigl-17-15.ngc +; lookinmg for why tal skinny tri ovveurs +; seems to happern mostly on final ornits +; use ZNR17-15 +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G19 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = 2.000 ; CPlane small for more test s per hr +#4 = 1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = -3.123 +#11 = 0 +#12 = 0 + +o110 while [#1 LT #2] + + ;g10l2p1 x0 y0 z0; UNSHIFT + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 y0 z0 ; above bore ctr + g0 X#3 ; move to Cplane + g0 X#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0X0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/XposWiglNR17-15.ngc b/configs/sim/axis/sedm/ngc/1orb/XposWiglNR17-15.ngc new file mode 100644 index 00000000000..15a9943be4b --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/XposWiglNR17-15.ngc @@ -0,0 +1,63 @@ +;XnegsWigl-17-15.ngc +; lookinmg for why tal skinny tri ovveurs +; seems to happern mostly on final ornits +; use ZNR17-15 +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G19 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = 5.000 ; CPlane small for more test s per hr +#4 = 1.0 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0X0; already + G0Y0Z0; already + + ;//////////////////// Posn 1 + g10l2p1 x#3 y0 z0 ; cut ref pt /datum + + g0 y0 z0 ; above bore ctr + g0 X#4 ; move to Rplabe aboce bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0X0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/YnegWiglNR17-15.ngc b/configs/sim/axis/sedm/ngc/1orb/YnegWiglNR17-15.ngc new file mode 100644 index 00000000000..c16674c3dfb --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/YnegWiglNR17-15.ngc @@ -0,0 +1,56 @@ +;YnegsWigl-17-15.ngc +; lookinmg for why tal skinny tri ovveurs +; seems to happern mostly on final ornits +; use ZNR17-15 +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G18 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.0 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x1 y 0 z1 ;was x0 y0 z2; DATUM for cut #1 + g0 x0 y0 + z#4;RPlane rel to DATUM at G53 2.5 now + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/YposWiglNR17-15.ngc b/configs/sim/axis/sedm/ngc/1orb/YposWiglNR17-15.ngc new file mode 100644 index 00000000000..5a24a0b864d --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/YposWiglNR17-15.ngc @@ -0,0 +1,56 @@ +;YposWigl-17-15.ngc +; lookinmg for why tal skinny tri ovveurs +; seems to happern mostly on final ornits +; use ZNR17-15 +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G18 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.0 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x1 y 0 z1 ;was x0 y0 z2; DATUM for cut #1 + g0 x0 y0 + z#4;RPlane rel to DATUM at G53 2.5 now + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/ZnegWiglNR17-15-02.ngc b/configs/sim/axis/sedm/ngc/1orb/ZnegWiglNR17-15-02.ngc new file mode 100644 index 00000000000..c7d0c1119db --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/ZnegWiglNR17-15-02.ngc @@ -0,0 +1,69 @@ +;ZnegWigl-17-15-02.ngc +; lookinmg for why tal skinny tri ovveurs +; seems to happern mostly on final ornits +; use ZNR17-15 +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-0.304 Q1.0 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G0X0Y0Z0 ; dont really so this tool would touch wkpc + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro +;DRO shows Z 0 + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 100 (limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +0.5 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + ; DRO shows Z 0 + + G0Z#3; CPlane + ;Z moves and DRO shows Z 2.0 + ;********** Z is at G53 Z2.0 + ;//////////////////// Posn 1 + g10l2p1 x1 y 0 z1 ;DATUM for Z is G53 Z1 + ; DRO shows Z1,0 shiftewd hairball + ;*********** Z msrd from G53 Z1, dro shows shifted Z1.0 + g0 x0 y0 + z#4 ;RPlane rel to DATUM + ; Z moves to 0.5 above G53 Z 1.0 + ; DRO shows shifted X at 0.5 + ; and unshifted Z at G53 1.5 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + ;DRO shows unshifted G53 Z1.5 + G0Z#3;CPlane abso mc coords + ;DRO shows unshifted G63 Z2.0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off Jump if it was left on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/ZnegWiglNR17-15.ngc b/configs/sim/axis/sedm/ngc/1orb/ZnegWiglNR17-15.ngc new file mode 100644 index 00000000000..23172de08bd --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/ZnegWiglNR17-15.ngc @@ -0,0 +1,56 @@ +;ZnegWigl-17-15.ngc +; lookinmg for why tal skinny tri ovveurs +; seems to happern mostly on final ornits +; use ZNR17-15 +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.0 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x1 y 0 z1 ;was x0 y0 z2; DATUM for cut #1 + g0 x0 y0 + z#4;RPlane rel to DATUM at G53 2.5 now + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/ZnegWiglNR25-15.ngc b/configs/sim/axis/sedm/ngc/1orb/ZnegWiglNR25-15.ngc new file mode 100644 index 00000000000..b5b97ecafdf --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/ZnegWiglNR25-15.ngc @@ -0,0 +1,54 @@ +;SEDMmulDstraight3.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-0.304 Q1.0 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P1 Q0.05; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +1.000 ; CPlane small for more test s per hr +#4 = +0.5 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/ZposWiglNR17-15.ngc b/configs/sim/axis/sedm/ngc/1orb/ZposWiglNR17-15.ngc new file mode 100644 index 00000000000..63e1cf85d4e --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/ZposWiglNR17-15.ngc @@ -0,0 +1,56 @@ +;ZnegWigl-17-15.ngc +; lookinmg for why tal skinny tri ovveurs +; seems to happern mostly on final ornits +; use ZNR17-15 +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.0 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x1 y 0 z1 ;was x0 y0 z2; DATUM for cut #1 + g0 x0 y0 + z#4;RPlane rel to DATUM at G53 2.5 now + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEtab19-NR25-10.ngc b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEtab19-NR25-10.ngc new file mode 100644 index 00000000000..4d8f3b7d103 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEtab19-NR25-10.ngc @@ -0,0 +1,54 @@ +;nuZnegWiglEyab19-NR25-12.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-0.304 Q1.0 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0.05; OrbType SQR, no Wigl for more tests per hr + M160 P19 Q0.508 ; etabnum, MsrdUNS + M161 P25 Q10 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +1.000 ; CPlane small for more test s per hr +#4 = +0.5 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEtab20-NR25-12.ngc b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEtab20-NR25-12.ngc new file mode 100644 index 00000000000..825d66e0f1c --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEtab20-NR25-12.ngc @@ -0,0 +1,54 @@ +;nuZnegWiglEyab19-NR25-12.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-0.304 Q1.0 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0.05; OrbType SQR, no Wigl for more tests per hr + M160 P20 Q0.635 ; etabnum, MsrdUNS + M161 P25 Q12 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +1.000 ; CPlane small for more test s per hr +#4 = +0.5 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEtab21-NR25-11.ngc b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEtab21-NR25-11.ngc new file mode 100644 index 00000000000..a3df5888488 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEtab21-NR25-11.ngc @@ -0,0 +1,54 @@ +;nuZnegWiglEtab21-NR25-11.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-0.304 Q1.0 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0.05; OrbType SQR, no Wigl for more tests per hr + M160 P21 Q0.762 ; etabnum, MsrdUNS + M161 P25 Q11 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +1.000 ; CPlane small for more test s per hr +#4 = +0.5 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEyab19-NR25-12.ngc b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEyab19-NR25-12.ngc new file mode 100644 index 00000000000..38f093c07cf --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEyab19-NR25-12.ngc @@ -0,0 +1,54 @@ +;nuZnegWiglEyab19-NR25-12.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-0.304 Q1.0 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P1 Q0.05; OrbType SQR, no Wigl for more tests per hr + M160 P19 Q0.635 ; etabnum, MsrdUNS + M161 P25 Q12 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +1.000 ; CPlane small for more test s per hr +#4 = +0.5 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEyab20-NR25-12.ngc b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEyab20-NR25-12.ngc new file mode 100644 index 00000000000..ac44850a72a --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglEyab20-NR25-12.ngc @@ -0,0 +1,54 @@ +;nuZnegWiglEyab19-NR25-12.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-0.304 Q1.0 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P1 Q0.05; OrbType SQR, no Wigl for more tests per hr + M160 P20 Q0.685 ; etabnum, MsrdUNS + M161 P25 Q12 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +1.000 ; CPlane small for more test s per hr +#4 = +0.5 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglNR17-15.ngc b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglNR17-15.ngc new file mode 100644 index 00000000000..e8c0da4aec8 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1orb/nuZnegWiglNR17-15.ngc @@ -0,0 +1,56 @@ +;nuZnegWigl-17-15.ngc +; lookinmg for why tal skinny tri ovveurs +; seems to happern mostly on final ornits +; use ZNR17-15 +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P19 Q0.635 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.0 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x1 y 0 z1 ;was x0 y0 z2; DATUM for cut #1 + g0 x0 y0 + z#4;RPlane rel to DATUM at G53 2.5 now + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1straight/1straightXneg.ngc b/configs/sim/axis/sedm/ngc/1straight/1straightXneg.ngc new file mode 100644 index 00000000000..65d388536c8 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1straight/1straightXneg.ngc @@ -0,0 +1,63 @@ +;1straightXneg.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G19 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = 2.000 ; CPlane small for more test s per hr +#4 = 1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = -3.123 +#11 = 0 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 y0 z0 ; above bore ctr + g0 X#3 ; move to Cplane + g0 X#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0X0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1straight/1straightXpos.ngc b/configs/sim/axis/sedm/ngc/1straight/1straightXpos.ngc new file mode 100644 index 00000000000..12efb8b3fe2 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1straight/1straightXpos.ngc @@ -0,0 +1,63 @@ +;1straightXpos.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G19 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = -2.000 ; CPlane small for more test s per hr +#4 = -1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = +3.123 +#11 = 0 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 y0 z0 ; above bore ctr + g0 X#3 ; move to Cplane + g0 X#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0X0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1straight/1straightYneg.ngc b/configs/sim/axis/sedm/ngc/1straight/1straightYneg.ngc new file mode 100644 index 00000000000..7be35ddc41d --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1straight/1straightYneg.ngc @@ -0,0 +1,63 @@ +;1straightYneg.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G18 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = -3.123 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 z0 ; above bore ctr + g0 y#3 ; move to Cplane + g0 y#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Y0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1straight/1straightYpos.ngc b/configs/sim/axis/sedm/ngc/1straight/1straightYpos.ngc new file mode 100644 index 00000000000..683ebb4d9d5 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1straight/1straightYpos.ngc @@ -0,0 +1,63 @@ +;1straightYpos.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G18 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = -2.000 ; CPlane small for more test s per hr +#4 = -1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = +3.123 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 z0 ; above bore ctr + g0 y#3 ; move to Cplane + g0 y#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Y0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1straight/1straightZneg.ngc b/configs/sim/axis/sedm/ngc/1straight/1straightZneg.ngc new file mode 100644 index 00000000000..dd9e24bb333 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1straight/1straightZneg.ngc @@ -0,0 +1,64 @@ +;1straightZneg.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = 0 +#12 = -3.123 + + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 y0 ; above bore ctr + g0 z#3 ; move to Cplane + g0 z#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1straight/1straightZpos.ngc b/configs/sim/axis/sedm/ngc/1straight/1straightZpos.ngc new file mode 100644 index 00000000000..e95f832638e --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1straight/1straightZpos.ngc @@ -0,0 +1,64 @@ +;1straightZpos.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = -2.000 ; CPlane small for more test s per hr +#4 = -1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = 0 +#12 = +3.123 + + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 y0 ; above bore ctr + g0 z#3 ; move to Cplane + g0 z#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1straight/nu1straightZneg.ngc b/configs/sim/axis/sedm/ngc/1straight/nu1straightZneg.ngc new file mode 100644 index 00000000000..e8c4a3bd4fe --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1straight/nu1straightZneg.ngc @@ -0,0 +1,64 @@ +;1straightZneg.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, no Wigl for more tests per hr + M160 P19 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = 0 +#12 = -3.123 + + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 y0 ; above bore ctr + g0 z#3 ; move to Cplane + g0 z#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/WiglXpos.ngc b/configs/sim/axis/sedm/ngc/1wigl/WiglXpos.ngc new file mode 100644 index 00000000000..a5a0ca95b49 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/WiglXpos.ngc @@ -0,0 +1,63 @@ +;WuglXpos.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0.050; OrbType SQR, 50 Wigl + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G19 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = -2.000 ; CPlane small for more test s per hr +#4 = -1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = +3.123 +#11 = 0 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 y0 z0 ; above bore ctr + g0 X#3 ; move to Cplane + g0 X#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0X0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/WiglYneg.ngc b/configs/sim/axis/sedm/ngc/1wigl/WiglYneg.ngc new file mode 100644 index 00000000000..41be562c887 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/WiglYneg.ngc @@ -0,0 +1,63 @@ +;WuglYneg.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0.050 ; OrbType SQR, 50 Wigl + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G18 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = -3.123 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 z0 ; above bore ctr + g0 y#3 ; move to Cplane + g0 y#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Y0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/WiglYpos.ngc b/configs/sim/axis/sedm/ngc/1wigl/WiglYpos.ngc new file mode 100644 index 00000000000..0dd08fb275e --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/WiglYpos.ngc @@ -0,0 +1,63 @@ +;WuglYpos.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0.050 ; OrbType SQR, 50 Wigl + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G18 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = -2.000 ; CPlane small for more test s per hr +#4 = -1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = +3.123 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 z0 ; above bore ctr + g0 y#3 ; move to Cplane + g0 y#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Y0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/WiglZneg.ngc b/configs/sim/axis/sedm/ngc/1wigl/WiglZneg.ngc new file mode 100644 index 00000000000..2af66d7cb07 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/WiglZneg.ngc @@ -0,0 +1,63 @@ +;WuglZneg.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0.050; OrbType SQR, 50 Wigl + M160 P34 Q0.254 ; etabnum, MsrdUNS M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = 0 +#12 = -3.123 + + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 y0 ; above bore ctr + g0 z#3 ; move to Cplane + g0 z#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/WiglZpos.ngc b/configs/sim/axis/sedm/ngc/1wigl/WiglZpos.ngc new file mode 100644 index 00000000000..0fd70ace9f7 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/WiglZpos.ngc @@ -0,0 +1,64 @@ +;WuglZpos.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0.050 ; OrbType SQR, 50 Wigl + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = -2.000 ; CPlane small for more test s per hr +#4 = -1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = 0 +#12 = +3.123 + + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 y0 ; above bore ctr + g0 z#3 ; move to Cplane + g0 z#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/WigltXneg.ngc b/configs/sim/axis/sedm/ngc/1wigl/WigltXneg.ngc new file mode 100644 index 00000000000..90a7336889a --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/WigltXneg.ngc @@ -0,0 +1,63 @@ +;WuglXneg.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0.050; OrbType SQR, 50 Wigl + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G19 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = 2.000 ; CPlane small for more test s per hr +#4 = 1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = -3.123 +#11 = 0 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 y0 z0 ; above bore ctr + g0 X#3 ; move to Cplane + g0 X#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0X0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/1wiglXneg.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglXneg.ngc new file mode 100644 index 00000000000..2f5624aebfc --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglXneg.ngc @@ -0,0 +1,71 @@ +;1wiglXneg.ngc +; +; +; CUTS x NEG g19 TOWARDS OPER left +; X -11 is where wiggl begins, this is RPlane, stock begins at -10 +; cut is from -9.00 to -11.000 + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G19 + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (counter) +#2 = 1 (limit) +#3 = -2 ; +#4 = 1.000 ; RPlane 2 right of datum + +;pre posn +G10L2P1 X0 Y0 Z0 ; UNSHIFT +G0 X0 ; PrePosn right of satum +G0 Y0 Z 5; PRE POSN,while unshifted, + +; for XNEG cut , get further X POS than DATUM (later g10l2p1x?y?z? ) + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + g10l2p1 x#3 y0 z2 ; DATURM + g0 y0 z0 ; center over DATUM + G0 X#4 ;get close to DATUM on open side od wekpc + ;//////////////////// Cut 1 code + o210 call + ;//////////////////// + g10l2p1 x0 y0 z0 ; UNSHIFT + ; endds at RPlane above DATUM on ctr + G0 X0 ; rtn to pre posn + G0 y0 z5 ; << thes 2 can be 1 line +;\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +;rdundant G10L2P1 X0 Y0 Z0 ;UNSHIFT after loo despite loop also unchifting + +;etn to pre posn +;redundant G0 X8 Y0 Z 5 ; + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 + +; can sub be after M02? YES +; can sub use # vars? NO killsa comp +o210 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.304 Q+1.00 ; FD RPlane + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 ; BegNR EndNR + M00 + M198 +o210 endsub +; /////////////// end subs //////// +% + diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/1wiglXpos.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglXpos.ngc new file mode 100644 index 00000000000..a077baaddad --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglXpos.ngc @@ -0,0 +1,61 @@ +;1wiglXXpos.ngc +; +; CUTS x POS g19 TOWARDS OPER right +; X+2 Y0 Z5 is DATUM. the cut is rtelative to DATUN +; sub gets all parms from Mcodes +; M162 P1.304 Q-1.00 +; set P as FullDepth ( per print) +; set Q as RPlane, a dist above DATUM where power is turned on +; + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G19 ; defines ToolAxis as + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (counter) +#2 = 1 (limit) +#3 = +2 ( ToolAxis Datum) +#4 = -1.000 ( RPlane above DATUM, in free space outside of stock) + +;------------------ pre posn +G10L2P1 X0 Y0 Z0 ; UNSHIFT +G0 X0 ; PrePosn to LEFT of satum ( Right of DATUN is inside stock) +G0 Y0 Z 5; PRE POSN,while unshifted, + +; loop framework +o110 while [#1 LT #2] + g10l2p1 x#3 y0 z2 ; DATUM + g0 y0 z0 ; center over DATUM + G0 X#4 ;get to RPlaane over DATUM + ; + o210 call + ; + g10l2p1 x0 y0 z0 ; UNSHIFT + ; sub call endds at RPlane above DATUM on ctr + G0 X0 ; rtn to pre posn + G0 y0 z5 ; << thes 2 can be 1 line + ; + #1 = [#1 + 1] +o110 endwhile +M197 ( turn off JumpENA if leaft on ) +M02 + +; subs can be after M02, just to unclutter +o210 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P1.304 Q-1.00 ; FD RPlane + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 ; BegNR EndNR + M00 + M198 +o210 endsub +; +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/1wiglYneg.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglYneg.ngc new file mode 100644 index 00000000000..6e29b172896 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglYneg.ngc @@ -0,0 +1,61 @@ +;1wiglYnegD.ngc +; +; CUTS Y NEG g18 TOWARDS OPER +; Y-2 Y0 Z5 is DATUM. the cut is rtelative to DATUN +; sub gets all parms from Mcodes +; M162 P-1.304 Q+1.00 +; set P as FullDepth ( per print) +; set Q as RPlane, a dist above DATUM where power is turned on +; + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G18 ; defines ToolAxis as Y + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (counter) +#2 = 1 (limit) +#3 = -2 ( ToolAxis Datum) +#4 = +1.000 ( RPlane above DATUM, in free space outside of stock) + +;------------------ pre posn +G10L2P1 X0 Y0 Z0 ; UNSHIFT +G0 Y0 ; PrePosn to LEFT of satum ( Right of DATUN is inside stock) +G0 X0 Z 5; PRE POSN,while unshifted, + +; loop framework +o110 while [#1 LT #2] + g10l2p1 x0 y#3 z2 ; DATUM + g0 x0 z0 ; center over DATUM + G0 y#4 ;get to RPlaane over DATUM + ; + o210 call + ; + g10l2p1 x0 y0 z0 ; UNSHIFT + ; sub call endds at RPlane above DATUM on ctr + G0 y0 ; rtn to pre posn + G0 x0 z5 ; << thes 2 can be 1 line + ; + #1 = [#1 + 1] +o110 endwhile +M197 ( turn off JumpENA if leaft on ) +M02 + +; subs can be after M02, just to unclutter +o210 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.304 Q+1.00 ; FD RPlane + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 ; BegNR EndNR + M00 + M198 +o210 endsub +; +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/1wiglYpos.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglYpos.ngc new file mode 100644 index 00000000000..efd27eac08b --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglYpos.ngc @@ -0,0 +1,62 @@ +;1wiglYpos.ngc +; +; CUTS Y POS g19 TOWARDS OPER right +; Y+2 Y0 Z5 is DATUM. the cut is rtelative to DATUN +; sub gets all parms from Mcodes +; M162 P1.304 Q-1.00 +; set P as FullDepth ( per print) +; set Q as RPlane, a dist above DATUM where power is turned on +; + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G18 ; defines ToolAxis as Y + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (counter) +#2 = 1 (limit) +#3 = +2 ( ToolAxis Datum) +#4 = -1.000 ( RPlane above DATUM, in free space outside of stock) + +;------------------ pre posn +G10L2P1 X0 Y0 Z0 ; UNSHIFT +G0 Y0 ; PrePosn to LEFT of satum ( Right of DATUN is inside stock) +G0 X0 Z 5; PRE POSN,while unshifted, + +; loop framework +o110 while [#1 LT #2] + g10l2p1 x0 y#3 z2 ; DATUM + g0 x0 z0 ; center over DATUM + G0 y#4 ;get to RPlaane over DATUM + ; + o210 call + ; + g10l2p1 x0 y0 z0 ; UNSHIFT + ; sub call endds at RPlane above DATUM on ctr + G0 y0 ; rtn to pre posn + G0 x0 z5 ; << thes 2 can be 1 line + ; + #1 = [#1 + 1] +o110 endwhile +M197 ( turn off JumpENA if leaft on ) +M02 + +; subs can be after M02, just to unclutter +o210 sub + ; just wigl .050 seep .01 above .01wiglrad + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P1.304 Q-1.00 ; FD RPlane + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 ; BegNR EndNR + M00 + M198 +o210 endsub +; +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/1wiglZneg.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglZneg.ngc new file mode 100644 index 00000000000..f79fa6f7ce2 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglZneg.ngc @@ -0,0 +1,46 @@ +;1wiglZneg.ngc +;---- Preamble----- +G21 ; mm +G90 ; absolute +G17 ; defines ToolAxis as Z +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F000 ; wishful thinnking +; ------ vars ------- +#1 = 0 (counter) +#2 = 1 (limit) +#3 = -2.00 ( ToolAxis Datum) +#4 = +1.000 ( RPlane above DATUM, in free space outside of stock) +#5 = 5.000 ( Cplnae clearanve plane above clamps) +;-------- pre posn ------ +G10 L2 P1 X0 Y0 Z0; UNSHIFT +G0 Z#5; move to Cplane +;-------- loop ------ +o110 while [#1 LT #2] + g10 l2 p1 x0 y0 z#3 + g0 x0 y0 + G0 z#4 + o210 call + g10 l2 p1 x0 y0 z0 ; UNSHIFT + G0 z#5 ; rtn to pre posn + G0 x0 y0 + #1 = [#1 + 1] +o110 endwhile +; ---- pre exit +M197 ( turn off JumpENA if left on ) +M02 +; ------- subrtns ----- +; subs can be after M02, just to unclutter +o210 sub + M66 E0 L0 + M199 + M162 P-1.304 Q+1 + M163 P0 Q0.025 + M160 P88888834 Q0.254 + M161 P25 Q25 + ;-------M166 P0 ;ue gui to yuirn on jump + ;-------M165 P1 ; pitch not used + M00 + M198 +o210 endsub +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/1wiglZpos.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglZpos.ngc new file mode 100644 index 00000000000..e505967c57f --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/1wiglZpos.ngc @@ -0,0 +1,71 @@ +;1wiglZpos.ngc +; +; CUTS Z POS g17 'down' +; x0 y0 z0 is DATUM (z#3) +; sub gets all parms from Mcodes +; M162 P+1.304 Q-1.00 +; set P as FullDepth ( per print) +; set Q as RPlane, a dist above DATUM where power is turned on +; + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G17 ; defines ToolAxis as Y + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (counter) +#2 = 1 (limit) +#3 = +4 ( ToolAxis Datum) +#4 = -1.000 ( RPlane above DATUM, in free space outside of stock) + +;------------------ pre posn +g0x10; start here juist so tool is outta the way +g0z5y0 + + +G10L2P1 X0 Y0 Z0 ; UNSHIFT +G0 Z0 ; PrePosn to LEFT of satum ( Right of DATUN is inside stock) +G0 X0 Y0 ; PRE POSN,while unshifted, + +; loop framework +o110 while [#1 LT #2] + g10l2p1 x0 y0 z#3 ; DATUM z+2 + g0 x0 y0 ; center over DATUM + G0 z#4 ;get to z+1 RPlaane over DATUM + ; + o210 call + ; + g10l2p1 x0 y0 z0 ; UNSHIFT + ; sub call endds at RPlane above DATUM on ctr + G0 z0 ; rtn to pre posn + G0 x0 y0 ; << thes 2 can be 1 line + ; + #1 = [#1 + 1] +o110 endwhile + +g0x10 +g0z5 + +M197 ( turn off JumpENA if leaft on ) +M02 + +; subs can be after M02, just to unclutter +o210 sub + ; just wigl .050 seep .01 above .01wiglrad + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P+1.304 Q-1.00 ; FD RPlane + ; NOTE bash m1nn scrupt wonr pass #n vars + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P25 Q25 ; BegNR EndNR + M00 + M198 +o210 endsub +; +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/tarpTri.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/tarpTri.ngc new file mode 100644 index 00000000000..b4bf6e9688f --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/tarpTri.ngc @@ -0,0 +1,80 @@ +;trapTri.ngc +; +; sometimes i get no stairs +; just liL +;tehn a line to ?RufPtTupl, +;then a line to sSPO +; incosistant, rare +; so loop the cut in smae place +; and use dbug prints, naybe traps to catch it +; +; +; i have spcl code for when 1st stepop ofsatairs gets a BWD +; suing a ctr +; but maybe nore than 1 of tyhe 1stmoives on stairs is BWD +; +; CUTS Z NEG g17 'down' +; x0 y-2 z2 is DATUM (z#3) +; sub gets all parms from Mcodes +; M162 P-1.304 Q+1.00 +; set P as FullDepth ( per print) +; set Q as RPlane, a dist above DATUM where power is turned on +; + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G17 ; defines ToolAxis as Y + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (counter) +#2 = 100 (limit) +#3 = -2.00 ( ToolAxis Datum) +#4 = +1.000 ( RPlane above DATUM, in free space outside of stock) + +;------------------ pre posn +G10L2P1 X0 Y0 Z0 ; UNSHIFT + +G0 Z5 ; PrePosn to LEFT of satum ( Right of DATUN is inside stock) +G0 X0 Y0 ; PRE POSN,while unshifted, + +; loop framework +o110 while [#1 LT #2] + g10l2p1 x0 y0 z#3 ; DATUM + g0 x0 y0 ; center over DATUM + G0 z#4 ;get to RPlaane over DATUM + ; + o210 call + ; + g10l2p1 x0 y0 z0 ; UNSHIFT + ; sub call endds at RPlane above DATUM on ctr + G0 z5 ; rtn to pre posn + G0 x0 y0 ; << thes 2 can be 1 line + ; + #1 = [#1 + 1] +o110 endwhile +M197 ( turn off JumpENA if leaft on ) +M02 + +; subs can be after M02, just to unclutter +o210 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-0.304 Q+1.00 ; FD RPlane + + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q25 ; BegNR EndNR + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o210 endsub +; +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/trapTri.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/trapTri.ngc new file mode 100644 index 00000000000..cd77e11f781 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/trapTri.ngc @@ -0,0 +1,84 @@ +;trapTri.ngc +; err tri happeb at top stair +; so get more test per hr by making dethh small\; +; also Z CPlane lowe +; +; sometimes i get no stairs +; just liL +;tehn a line to ?RufPtTupl, +;then a line to sSPO +; incosistant, rare +; so loop the cut in smae place +; and use dbug prints, naybe traps to catch it +; +; +; i have spcl code for when 1st stepop ofsatairs gets a BWD +; suing a ctr +; but maybe nore than 1 of tyhe 1stmoives on stairs is BWD +; +; CUTS Z NEG g17 'down' +; x0 y-2 z2 is DATUM (z#3) +; sub gets all parms from Mcodes +; M162 P-1.304 Q+1.00 +; set P as FullDepth ( per print) +; set Q as RPlane, a dist above DATUM where power is turned on +; + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G17 ; defines ToolAxis as Y + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (counter) +#2 = 1000 (limit) +#3 = -2.00 ( ToolAxis Datum) +#4 = +1.000 ( RPlane above DATUM, in free space outside of stock) + +;------------------ pre posn +G10L2P1 X0 Y0 Z0 ; UNSHIFT + +G0 Z0.5 ; PrePosn to LEFT of satum ( Right of DATUN is inside stock) +G0 X0 Y0 ; PRE POSN,while unshifted, + +; loop framework +o110 while [#1 LT #2] + g10l2p1 x0 y0 z#3 ; DATUM + g0 x0 y0 ; center over DATUM + G0 z#4 ;get to RPlaane over DATUM + ; + o210 call + ; + g10l2p1 x0 y0 z0 ; UNSHIFT + ; sub call endds at RPlane above DATUM on ctr + G0 z0.5 ; rtn to pre posn + G0 x0 y0 ; << thes 2 can be 1 line + ; + #1 = [#1 + 1] +o110 endwhile +M197 ( turn off JumpENA if leaft on ) +M02 + +; subs can be after M02, just to unclutter +o210 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-0.104 Q+1.00 ; was .304 ; FD RPlane + ;M162 P-0.110 Q+1.00 ; was .104 abd saw V from entry to exit NOT A PROB just aestheticc + + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q25 ; BegNR EndNR + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o210 endsub +; +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/wiglAllOrbs-4x10.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/wiglAllOrbs-4x10.ngc new file mode 100644 index 00000000000..6198195c828 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/wiglAllOrbs-4x10.ngc @@ -0,0 +1,144 @@ +;wiglAllOrbs-4x10.ngc not 4x10 just x4 and same place redrawn +; that allows me to seleep and still find bad detores +; so get rid of inc'ing Y by 2 more +; +;all posn do wigl and all orbits sqr +; sumply always call o240 +o210 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.000 ; FD RPlane + + M163 P0 Q0.05 ; OrbType Circle, WiglRad 50um5 + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q25 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o210 endsub + +o220 sub + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.000 ; FD RPlane + + M163 P0 Q0.0 ; OrbType Circle, WiglRad 50um5 + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q24 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o220 endsub + +o230 sub + ; just last orb + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + + M163 P0 Q0.0 ; OrbType Circle, EiglRad 50um + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P15 Q15 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o230 endsub +;end just last orb + +o240 sub + ; wigl and all orbits + M66 E0 L0 ;QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; start PV control + M162 P-1.254 Q1.0 ; FD RPlabe + + M163 P1 Q0.012 ; OrbType Circle, EiglRad 50um + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q15 ; BegNR EndNR + + M166 P0 ; no jump + M165 P1 ; Pitch == 1 + M00 + M198 +o240 endsub +;end wigl and all orbits + +; /////////////// end subs //////// +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +T2 +M6 + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 10 (limit) +#3 = +5.000 ; CPlane +#4 = +1.000 ; RPlane + +#5 = 0 ; yaxis + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0 ; UNSHIFT + G0Z#3 ; CPlane + + ;-DETAIL 1 ------------- + g10l2p1 x10 y#5 z-2 ;DATUM 1 + g0x0y0 + z#4 ;RPlane rel to DATUM + o240 call + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3 ;CPlane abso mc coords + + ;-DETAIL 2------------------------- + g10l2p1 x12 y#5 z-2 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + o240 call ; cut Detail 2 + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + ;-Detail 3 + g10l2p1 x14 y#5 z-2 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + o240 call ; cut dertail 3 + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1 x16 y#5 z-2 ; set DATUM 4 + g0x0y0 + z#4 + o240 call ; cut detail 4 + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + #1 = [#1 + 1] + ; DO NOT INC Y #5 = [#5 + 2] + ; use Y view and wasily see any bads detours +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 ;UNSHIFT +G0Z#3 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/1wigl/old/x.ngc b/configs/sim/axis/sedm/ngc/1wigl/old/x.ngc new file mode 100644 index 00000000000..0a8f83a9be0 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/1wigl/old/x.ngc @@ -0,0 +1,43 @@ +;1wiglZneg.ngc +;///////////////////// PREAMBLE +G21 +G90 +G17 +G61 +G64 P0 +F5000 +#1 = 0 +#2 = 1 +#3 = -2.00 +#4 = +1.000 +#5 = 5.000 +G10L2P1 X0 Y0 Z0 +G0 Z#5 + +o110 while [#1 LT #2] +g10 l2 p1 x10 y0 z#3 +g0 x0 y0 +G0 z#4 +o210 call +g10 l2 p1 x0 y0 z0 +G0z#5 +G0x0y0 +#1 = [#1 + 1] +o110 endwhile + +M197 +M02 +o210 sub +M66E0L0 +M199 +M162P-1.304Q+1.00 +M163 P0 Q0.025 +M160 P88888834 Q0.254 +M161 P25 Q25 +;M166 P0 +;M165 P1 +M00 +M198 +o210 endsub + +% diff --git a/configs/sim/axis/sedm/ngc/BADjumpsfromRufPtToEntryPt-SEDMmultDStraight3.ngc b/configs/sim/axis/sedm/ngc/BADjumpsfromRufPtToEntryPt-SEDMmultDStraight3.ngc new file mode 100644 index 00000000000..b4b22c7ec31 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/BADjumpsfromRufPtToEntryPt-SEDMmultDStraight3.ngc @@ -0,0 +1,91 @@ +;SEDMmulDstraight3.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + + M162 P-1.304 Q1.0 ; FD RPlabe + + M163 P0 Q0.05; OrbType Circle, EiglRad 50um + + M160 P34 Q0.254 ; etabnum, MsrdUNS + + M161 P15 Q15; BegNR EndNR + + M166 P0 ; no jump + + M165 P1; Pitch == 1 + + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) + +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + g10l2p1 x0 y0 z0; UNSHIFT + G53G0Z#3 ; CPlane is in mc coords + + g10l2p1 x1 y0 z2; DATUM for cut #1 + g0x0y0 ; at CPlane l;evel move to xy ctr of Cut #1 + z#4 ; rapid to RPlane ( 1mm above DATUM + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3 ;rapid to CPlane + + + g10l2p1x2y0z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + ; rapis to CPlane + g10l2p1x3y0z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#1 ; rapid to RPLANE + + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 ; rapid to CPlane + + g10l2p1x4y0z-1 ; set DATUM 4 + g0x0y0 ; rapid to ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10l2p1x0y0z0 ; UNSHIFT +G0Z#3 ; rapid to CPlane +G0X0Y0 ; rapid to oper's choce xy + +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/Last2orbs6ways/XnegNR17-15.ngc b/configs/sim/axis/sedm/ngc/Last2orbs6ways/XnegNR17-15.ngc new file mode 100644 index 00000000000..4c638a2f4ca --- /dev/null +++ b/configs/sim/axis/sedm/ngc/Last2orbs6ways/XnegNR17-15.ngc @@ -0,0 +1,63 @@ +;XnegNR17-15.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, 0 Wigl + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G19 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = 2.000 ; CPlane small for more test s per hr +#4 = 1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = -3.123 +#11 = 0 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 y0 z0 ; above bore ctr + g0 X#3 ; move to Cplane + g0 X#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0X0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/Last2orbs6ways/XposNR17-15.ngc b/configs/sim/axis/sedm/ngc/Last2orbs6ways/XposNR17-15.ngc new file mode 100644 index 00000000000..40d19e314c3 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/Last2orbs6ways/XposNR17-15.ngc @@ -0,0 +1,63 @@ +;XposXnegNR17-15.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, 0 Wigl + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G19 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = -2.000 ; CPlane small for more test s per hr +#4 = -1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = +3.123 +#11 = 0 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 y0 z0 ; above bore ctr + g0 X#3 ; move to Cplane + g0 X#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0X0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/Last2orbs6ways/YnegNR17-15.ngc b/configs/sim/axis/sedm/ngc/Last2orbs6ways/YnegNR17-15.ngc new file mode 100644 index 00000000000..80f7e308e8c --- /dev/null +++ b/configs/sim/axis/sedm/ngc/Last2orbs6ways/YnegNR17-15.ngc @@ -0,0 +1,63 @@ +;YnegXnegNR17-15.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0 ; OrbType SQR, 0 Wigl + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G18 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = -3.123 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 z0 ; above bore ctr + g0 y#3 ; move to Cplane + g0 y#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Y0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/Last2orbs6ways/YposNR17-15.ngc b/configs/sim/axis/sedm/ngc/Last2orbs6ways/YposNR17-15.ngc new file mode 100644 index 00000000000..89a47382406 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/Last2orbs6ways/YposNR17-15.ngc @@ -0,0 +1,63 @@ +;YposXnegNR17-15.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0 ; OrbType SQR, 0 Wigl + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G18 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = -2.000 ; CPlane small for more test s per hr +#4 = -1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = +3.123 +#12 = 0 + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 z0 ; above bore ctr + g0 y#3 ; move to Cplane + g0 y#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Y0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/Last2orbs6ways/ZnegNR17-15.ngc b/configs/sim/axis/sedm/ngc/Last2orbs6ways/ZnegNR17-15.ngc new file mode 100644 index 00000000000..6f8546dac40 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/Last2orbs6ways/ZnegNR17-15.ngc @@ -0,0 +1,64 @@ +;ZnegXnegNR17-15.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.304 Q+1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0; OrbType SQR, 0 Wigl + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = +2.000 ; CPlane small for more test s per hr +#4 = +1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = 0 +#12 = -3.123 + + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 y0 ; above bore ctr + g0 z#3 ; move to Cplane + g0 z#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/Last2orbs6ways/ZposNR17-15.ngc b/configs/sim/axis/sedm/ngc/Last2orbs6ways/ZposNR17-15.ngc new file mode 100644 index 00000000000..351f462aa2f --- /dev/null +++ b/configs/sim/axis/sedm/ngc/Last2orbs6ways/ZposNR17-15.ngc @@ -0,0 +1,64 @@ +;ZposXnegNR17-15.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.304 Q-1.00 ; more tests per hr lookimg fdor bad tri from peri tto SPO + M163 P0 Q0 ; OrbType SQR, 0 Wigl + M160 P88888834 Q0.254 ; etabnum, MsrdUNS + M161 P17 Q15 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z5 ;prepositiomning is done with G17 in mind +G0X0Y0 ; after datum is set, thnik in G1? ( whatever) +G0Z0 ; until then, Z 1st XY 2nd + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (was 100 limit) +#3 = -2.000 ; CPlane small for more test s per hr +#4 = -1.000 ; RPlane small for more test s per hr + +; unshigted ordinates of datum ( cut posn ) +#10 = 0 +#11 = 0 +#12 = +3.123 + + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x#10 y#11 z#12 ; cut ref pt /datum + + g0 x0 y0 ; above bore ctr + g0 z#3 ; move to Cplane + g0 z#4 ; move to Rplane above bore ctr + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z0 + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z5 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDM-1XmultDStraight3.ngc b/configs/sim/axis/sedm/ngc/SEDM-1XmultDStraight3.ngc new file mode 100644 index 00000000000..9b240e42c25 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDM-1XmultDStraight3.ngc @@ -0,0 +1,175 @@ +;SEDMmult07.ngc +; hard to press PEEK bntn cuz yimw winoiw when bvtn enabled is small, so make it deeper DUH +; +; YAY DRO is relative to THID cut, and is Rel to MC0,0,0, when m,ovinge to nrxt cut +; one shift is wrong, bad copy and paste out of sync +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + ;M162 P-5.304 Q1.0 ; 22.11.2025 now Q is RPlane wasa -2.304 expect DRO + M162 P-1.304 Q1.0 ;shallower for more tests per hour + ; vvv P is orbtype (0circ 1swr) Q is wiglRAD) + M163 P0 Q0.05 + ; ^^^ was 0.01 .05 + M160 P34 Q0.254 + M161 P25 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 100 (limit) + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + g10l2p1 x0 y0 z0; remove shift + G53G0Z3; keep constant ht in wk area + g10l2p1 x1 y0 z2; add shift, mder from HERE + g0x0y0 + z1; move 1mm above ref pt (RPlane) + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0; remove offsets + G53G0Z3; keep constant ht in wk area + g10l2p1x2y0z1; set ref + g0x0y0 + z1; move 1mm above ref pt (RPlane) + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + g10l2p1x0y0z0 + G53G0Z3; keep constant ht in wk area + g10l2p1x3y0z0 + g0x0y0 + z1 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + g10l2p1x0y0z0 + G53G0Z3; keep constant ht in wk area + g10l2p1x4y0z-1 + g0x0y0 + z1 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y1z0 + g0x0y0 + z1 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + g10l2p1x3y1z0 + G0Z3; keep constant ht in wk area g10l2p1x3y1z0 + g0x0y0 + z1 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x1y3z0 + g0x0y0 + z1 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y1z0 + g0x0y0 + z1 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;************************* + ;//////////////////// Posn 1 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x1y1z0 + g0x0y0 + z1 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x1y2z0 + g0x0y0 + z1 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y2z0 + g0x0y0 + z1 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x3y2z0 + g0x0y0 + z1 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y2z0 + g0x0y0 + z1 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y3z0 + g0x0y0 + z1 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x3y3z0 + g0x0y0 + z1 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y3z0 + g0x0y0 + z1 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10l2p1x0y0z0 + +G0Z3 +G0X0Y0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDM-1x.ngc b/configs/sim/axis/sedm/ngc/SEDM-1x.ngc new file mode 100644 index 00000000000..355ffe87728 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDM-1x.ngc @@ -0,0 +1,39 @@ +; SEDM-1x.ngc +; 01.12.2025 +o200 sub + M66 E0 L0 ; NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; begin EDM mode by collectinf data from Mxcodes + M162 P-1.304 Q1.0 ; now Q is RPlane + M163 P0 Q0.05 ; P orbtype(0 circ 1sqr) Q wiglRAD + M160 P34 Q0.254 ; P Etab Q MsrdUNS + M161 P25 Q15 ; P BegNR W EndMR + M166 P0 ; jump OFF + M165 P1 ; pitch 1 + M00 ' necc for offsets while paused + M198 ; end EDM modde +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +; //////////////////// Posn 1 +g10l2p1 x0 y0 z0; UNshift +G53 G0 Z3; keep constant ht in wk area +g10l2p1 x1 y0 z2; add shift, mder from HERE +g0 x0 y0 ; get to new rwf pt (fromn g10 l2 p1.... +z1 ; move 1mm above ref pt (RPlane) +; +o200 call +; +; UNshift +G10l2p1x0y0z0 +; goto safe posn +G0Z3 +G0X0Y0 +; ////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDM06.ngc b/configs/sim/axis/sedm/ngc/SEDM06.ngc new file mode 100644 index 00000000000..e8764cbe69c --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDM06.ngc @@ -0,0 +1,212 @@ +;SEDM06.ngc +#12.11.2025 add queue buster +; +; begin untrapping Satate machibne +; +; +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking +;//////////////////// goto Posn 1 + +G0Z3 +G0X1Y0 ; CUT 1 @ x1 y0 +G0Z0 ; to make maths simple + +;//////////////////// prep cut posn 1 +;vvv +M199; done 1st M199 ; at top so SEDM creatd and enable early +;^^^ +M162 P-2.304 Q.255 ; expect DRO +M163 P0 Q00.10 +M160 P34 +M161 P25 Q25 +M166 P0 ; no jump +M165 P1 ; pitch +;//////////////////// cut posn 1 +M00 ; nrcc?? yes , alloes EDM cut + + +;//////////////////// tuen off axus.L.eoffset-enable +;vvv +M198 ; will be replaced by a trap at end of state machibne +;^^^ + +; SEDM comp should have hit last state of state machinbe +; and be stuck in a loop +; becuz SEDM.enable == Falsee +; LATERvvv M197 will break that loop +; by setting SEDM.enable True +; +;////// goto 2nd posn +G0X1 +G0X2Y0 +G0Z0 + +;vvv +M197 ; set EDM.restart True AFTER in posn BEFORE M1nn codes w data +;^^^ + +;vvv DO 2nd cut +M199; done 1st M199 ; at top so SEDM creatd and enable early +;^^^ +; 26.10.2025 try deep cut using non-updown methoc +M162 P-2.304 Q.255 ; expect DRO +M163 P0 Q00.10 +M160 P34 +M161 P25 Q25 +M166 P0 ; no jump +M165 P1 ; pitch + +M00 ; nrcc?? yes , alloes EDM cut +;vvv +M198 ; will be replaced by a trap at end of state machibne +;^^^ + +M197 + +; SEDM.restart should be FALSE ( if 2nd pass thru SM happened) + +G0Z1 ; move tp a 3rf posn +G0X3Y0 +; +G0Z2 ; vizual somethong after 2nd cut did 2nd cut iccur> + +;//////////////////////////////// +M02 +% + +///////////////////////////////////// +;SEDM03.ngc 12.11.2025 +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 ; enable SEDM comp + M00 + M198 ; disable SEDM comp +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 100 (limit) + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + G0Z3 + G0X1Y0 + G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + G0Z1 + G0X2Y0 + G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + G0Z1 + G0X3Y0 + G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + G0Z1 + G0X4Y0 + G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + G0Z1 + G0X4Y1 + G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + G0Z1 + G0X3Y1 + G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + G0Z1 + G0X2Y1 + G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + G0Z1 + G0X1Y1 + G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;************************* + ;//////////////////// Posn 1 + G0Z1 + G0X1Y2 + G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + G0Z1 + G0X2Y2 + G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + G0Z1 + G0X3Y2 + G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + G0Z1 + G0X4Y2 + G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + G0Z1 + G0X4Y3 + G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + G0Z1 + G0X3Y3 + G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + G0Z1 + G0X2Y3 + G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + G0Z1 + G0X1Y3 + G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z3 +G0X0Y0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDM0A.ngc b/configs/sim/axis/sedm/ngc/SEDM0A.ngc new file mode 100644 index 00000000000..128145fd9f7 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDM0A.ngc @@ -0,0 +1,133 @@ +;SEDM0A.ngc +; try o200 sub WORKS +; i should learn to automate a grid of cuts +; even randomize the spths and wiglrad +; +; +o200 sub + M197; harmless, SEDM.restart will be False before 1st cut w/o M197 + M199 + M162 P-2.304 Q.255 + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 + M165 P1 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking +;//////////////////// Posn 1 +G0Z3 +G0X1Y0 +G0Z0 +;//////////////////// Cut 1 code +o200 call +;//////////////////// posn 2 +G0Z2 +G0X2Y0 +G0Z0 +;//////////////////// CUT 2 code +o200 call +;//////////////////// posn 3 +G0Z2 +G0X3Y0 +G0Z0 +;//////////////////// CUT 3 cmds +o200 call +;//////////////////// posn 4 +G0Z2 +G0X4Y0 +G0Z0 +;//////////////////// CUT 4 ccmds +o200 call +;>>>>>>>>>>>>>>>>>>>>>>>>> +;//////////////////// Posn 5 +G0Z2 +G0X4Y1 +G0Z0 +;//////////////////// Cut 5 code +o200 call +;//////////////////// posn 6 +G0Z2 +G0X3Y1 +G0Z0 +;//////////////////// CUT 6 code +o200 call +;//////////////////// posn 7 +G0Z2 +G0X2Y1 +G0Z0 +;//////////////////// CUT 7 cmds +o200 call +;//////////////////// posn 8 +G0Z2 +G0X1Y1 +G0Z0 +;//////////////////// CUT 8 ccmds +o200 call +;>>>>>>>>>>>>>>>>>>>>>>>>> +;************************* +;//////////////////// Posn 1 +G0Z2 +G0X1Y2 +G0Z0 +;//////////////////// Cut 1 code +o200 call +;//////////////////// posn 2 +G0Z2 +G0X2Y2 +G0Z0 +;//////////////////// CUT 2 code +o200 call +;//////////////////// posn 3 +G0Z2 +G0X3Y2 +G0Z0 +;//////////////////// CUT 3 cmds +o200 call +;//////////////////// posn 4 +G0Z2 +G0X4Y2 +G0Z0 +;//////////////////// CUT 4 ccmds +o200 call +;>>>>>>>>>>>>>>>>>>>>>>>>> +;//////////////////// Posn 5 +G0Z2 +G0X4Y3 +G0Z0 +;//////////////////// Cut 5 code +o200 call +;//////////////////// posn 6 +G0Z2 +G0X3Y3 +G0Z0 +;//////////////////// CUT 6 code +o200 call +;//////////////////// posn 7 +G0Z2 +G0X2Y3 +G0Z0 +;//////////////////// CUT 7 cmds +o200 call +;//////////////////// posn 8 +G0Z2 +G0X1Y3 +G0Z0 +;//////////////////// CUT 8 ccmds +o200 call +;>>>>>>>>>>>>>>>>>>>>>>>>> +;************************* +;//////////////////// goto exit posn +G0Z3 +G0X0Y0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDM0Along.ngc b/configs/sim/axis/sedm/ngc/SEDM0Along.ngc new file mode 100644 index 00000000000..4f6d3061c46 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDM0Along.ngc @@ -0,0 +1,140 @@ +;SEDM0Alomg.ngc +; try o200 sub WORKS +; i should learn to automate a grid of cuts +; even randomize the spths and wiglrad +; +; +o200 sub + M197; harmless, SEDM.restart will be False before 1st cut w/o M197 + M199 + M162 P-2.304 Q.255 + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 + M165 P1 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 100 (limit) + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + G0Z3 + G0X1Y0 + G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + G0Z2 + G0X2Y0 + G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + G0Z2 + G0X3Y0 + G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + G0Z2 + G0X4Y0 + G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + G0Z2 + G0X4Y1 + G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + G0Z2 + G0X3Y1 + G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + G0Z2 + G0X2Y1 + G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + G0Z2 + G0X1Y1 + G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;************************* + ;//////////////////// Posn 1 + G0Z2 + G0X1Y2 + G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + G0Z2 + G0X2Y2 + G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + G0Z2 + G0X3Y2 + G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + G0Z2 + G0X4Y2 + G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + G0Z2 + G0X4Y3 + G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + G0Z2 + G0X3Y3 + G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + G0Z2 + G0X2Y3 + G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + G0Z2 + G0X1Y3 + G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z3 +G0X0Y0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDM0Asmall.ngc b/configs/sim/axis/sedm/ngc/SEDM0Asmall.ngc new file mode 100644 index 00000000000..dc053a3a06f --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDM0Asmall.ngc @@ -0,0 +1,41 @@ +;SEDM0Asmall.ngc +; 1st 2 posmns of SEDM0A.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q.255 ; wasa -2.304 expect DRO + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.0 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHUFT, msr as if G53 +;//////////////////// Posn 1 +G0Z3; this is G53 coords doe to UNSHIDT + +G10L2P1X1Y0Z1 ; NEW DATUM + +G0X0Y10 ; move over new datum +G0Z1.0; move to RPlaneDist abve new datum +;//////////////////// Cut 1 code +o200 call +;//////////////////// posn 2 +G10L2P1x0y0z0 ; msr like G53 +G0Z3 +;should be at +1 +0 +3 anf g54 is x0 y0 z0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMmult01.ngc b/configs/sim/axis/sedm/ngc/SEDMmult01.ngc new file mode 100644 index 00000000000..72bcf7aac43 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmult01.ngc @@ -0,0 +1,55 @@ +;SEDMmult01.ngc +; +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking +;//////////////////// Posn 1 +G0Z3 +G0X1Y0 ; CUT 1 @ x1 y0 +G0Z0 ; to make maths simple +;//////////////////// Cut Cmds +M199 +M162 P-2.304 Q.255 ; expect DRO +M163 P0 Q00.10 +M160 P34 +M161 P25 Q25 +M166 P0 ; no jump +M165 P1 ; pitch +M00 ; nrcc +M198 +;/////////// Posn 2 +G0X1 +G0X2Y0 +G0Z0 + +; set EDM.restart True AFTER in posn BEFORE M1nn codes w data +M197 + + +;/////// Cut Cmds +M199 +M162 P- 2.304 Q.255 ; expect DRO +M163 P0 Q00.10 +M160 P34 +M161 P25 Q25 +M166 P0 ; no jump +M165 P1 ; pitch +M00 ; nrcc +M198 + +M197 + +;//////// rtn to resting place easy oper unload/inspect +G0Z1 ; move tp a 3rf posn +G0X3Y0 +G0Z2 ; vizual somethong after 2nd cut did 2nd cut iccur> + +;//////////////////////////////// +M02 +% + +; vvv for ref +;M66 E0 L0; queue buster diff --git a/configs/sim/axis/sedm/ngc/SEDMmult02.ngc b/configs/sim/axis/sedm/ngc/SEDMmult02.ngc new file mode 100644 index 00000000000..b66cbc9962e --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmult02.ngc @@ -0,0 +1,44 @@ +;SEDMmult01.ngc +; +;//////// subs +o200 sub + ;M197 ;not necc 1st time, but keep macxro same + M199 + M162 P- 2.314 Q.255 ; added .010 fro rplane + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 ; nrcc + M198 + M197; ??? 2x in same macro?? +o200 endsub + +;//////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking +;//////////// Posn 1 +G0Z3 +G0X1Y0 ; CUT 1 @ x1 y0 +G0Z0.010 ; to make maths simple +;//////////////////// Cut Cmds +o200 call +;/////////// Posn 2 +G0Z2 +G0X2Y0 +G0Z0.010 +;/////// call cut +o200 call +;//////// rtn to resting place easy oper unload/inspect +G0Z3 +G0X0Y0 +;//////////////////////////////// +M02 +% + +; vvv for ref +;M66 E0 L0; queue buster diff --git a/configs/sim/axis/sedm/ngc/SEDMmult03.ngc b/configs/sim/axis/sedm/ngc/SEDMmult03.ngc new file mode 100644 index 00000000000..bfcdc8cf838 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmult03.ngc @@ -0,0 +1,58 @@ +;SEDMmult01.ngc +; damnit after last cut i do NBOT see QUIT on menu +;//////// subs +o200 sub + ;M197 ;not necc 1st time, but keep macxro same + M199 + M162 P- 2.314 Q.255 ; added .010 fro rplane + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 ; nrcc + M198 + M197; ??? 2x in same macro?? +o200 endsub + +;//////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking +;//////////// Posn 1 +G0Z3 +G0X1Y0 ; CUT 1 @ x1 y0 +G0Z0.010 ; to make maths simple +;//////////////////// Cut Cmds +o200 call +;/////////// Posn 2 +G0Z2 +G0X2Y0 +G0Z0.010 +;/////// call cut +o200 call + +;/////////// Posn 3 +G0Z2 +G0X3Y0 +G0Z0.010 +;/////// call cut +o200 call + +;/////////// Posn 4 +G0Z2 +G0X4Y0 +G0Z0.010 +;/////// call cut +o200 call + + +;//////// rtn to resting place easy oper unload/inspect +G0Z3 +G0X0Y0 + +;//////////////////////////////// +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMmult04.ngc b/configs/sim/axis/sedm/ngc/SEDMmult04.ngc new file mode 100644 index 00000000000..65a7e373be4 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmult04.ngc @@ -0,0 +1,104 @@ +;SEDMmult04.ngc +; damnit after last cut i do NBOT see QUIT on menu +; try use no subs +; ng ran all 4 cuts back to 0,0,3 and NO QWIT +;//////// subs +o200 sub + ;M197 ;not necc 1st time, but keep macxro same + M199 + M162 P- 2.314 Q.255 ; added .010 fro rplane + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 ; nrcc + M198 + M197; ??? 2x in same macro?? +o200 endsub + +;//////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking +;//////////// Posn 1 +G0Z3 +G0X1Y0 ; CUT 1 @ x1 y0 +G0Z0.010 ; to make maths simple +;//////////////////// Cut Cmds +;o200 call + ;M197 ;not necc 1st time, but keep macxro same + M199 + M162 P- 2.314 Q.255 ; added .010 fro rplane + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 ; nrcc + M198 + M197; ??? 2x in same macro?? + +G0Z3 +M02 +% + +;/////////// Posn 2 +G0Z2 +G0X2Y0 +G0Z0.010 +;/////// call cut +;o200 call + ;M197 ;not necc 1st time, but keep macxro same + M199 + M162 P- 2.314 Q.255 ; added .010 fro rplane + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 ; nrcc + M198 + M197; ??? 2x in same macro?? +;/////////// Posn 3 +G0Z2 +G0X3Y0 +G0Z0.010 +;/////// call cut +;o200 call + ;M197 ;not necc 1st time, but keep macxro same + M199 + M162 P- 2.314 Q.255 ; added .010 fro rplane + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 ; nrcc + M198 + M197; ??? 2x in same macro?? +;/////////// Posn 4 +G0Z2 +G0X4Y0 +G0Z0.010 +;/////// call cut +;o200 call + ;M197 ;not necc 1st time, but keep macxro same + M199 + M162 P- 2.314 Q.255 ; added .010 fro rplane + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 ; nrcc + M198 + M197; ??? 2x in same macro?? +;//////// rtn to resting place easy oper unload/inspect +G0Z3 +G0X0Y0 +;//////////////////////////////// +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMmult05.ngc b/configs/sim/axis/sedm/ngc/SEDMmult05.ngc new file mode 100644 index 00000000000..f16e860ecea --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmult05.ngc @@ -0,0 +1,80 @@ +;SEDM08.ngc +; begin untrapping Satate machibne +; +; +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking +;//////////////////// goto Posn 1 +G0Z3 +G0X1Y0 ; CUT 1 @ x1 y0 +G0Z0 ; to make maths simple + +;//////////////////// prep cut posn 1 +;vvv +M199; done 1st M199 ; at top so SEDM creatd and enable early +;^^^ +M162 P-2.304 Q.255 ; expect DRO +M163 P0 Q00.10 +M160 P34 +M161 P25 Q25 +M166 P0 ; no jump +M165 P1 ; pitch +;//////////////////// cut posn 1 +M00 ; nrcc?? yes , alloes EDM cut + + +;//////////////////// tuen off axus.L.eoffset-enable +;vvv +M198 ; will be replaced by a trap at end of state machibne +;^^^ + +; SEDM comp should have hit last state of state machinbe +; and be stuck in a loop +; becuz SEDM.enable == Falsee +; LATERvvv M197 will break that loop +; by setting SEDM.enable True +; +;////// goto 2nd posn +G0X1 +G0X2Y0 +G0Z0 + +;vvv +M197 ; set EDM.restart True AFTER in posn BEFORE M1nn codes w data +;^^^ + +;vvv DO 2nd cut +M199; done 1st M199 ; at top so SEDM creatd and enable early +;^^^ +; 26.10.2025 try deep cut using non-updown methoc +M162 P-2.304 Q.255 ; expect DRO +M163 P0 Q00.10 +M160 P34 +M161 P25 Q25 +M166 P0 ; no jump +M165 P1 ; pitch + +M00 ; nrcc?? yes , alloes EDM cut +;vvv +M198 ; will be replaced by a trap at end of state machibne +;^^^ + +M197 + +; SEDM.restart should be FALSE ( if 2nd pass thru SM happened) + +G0Z1 ; move tp a 3rf posn +G0X3Y0 +; +G0Z2 ; vizual somethong after 2nd cut did 2nd cut iccur> + +;//////////////////////////////// +M02 +% + +; vvv for ref +;M66 E0 L0; queue buster diff --git a/configs/sim/axis/sedm/ngc/SEDMmult06.ngc b/configs/sim/axis/sedm/ngc/SEDMmult06.ngc new file mode 100644 index 00000000000..b70bd8feaaa --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmult06.ngc @@ -0,0 +1,83 @@ +;SEDM06.ngc +#12.11.2025 add queue buster +; +; begin untrapping Satate machibne +; +; +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking +;//////////////////// goto Posn 1 + +G0Z3 +G0X1Y0 ; CUT 1 @ x1 y0 +G0Z0 ; to make maths simple + +;//////////////////// prep cut posn 1 +;vvv +M199; done 1st M199 ; at top so SEDM creatd and enable early +;^^^ +M162 P-2.304 Q.255 ; expect DRO +M163 P0 Q00.10 +M160 P34 +M161 P25 Q25 +M166 P0 ; no jump +M165 P1 ; pitch +;//////////////////// cut posn 1 +M00 ; nrcc?? yes , alloes EDM cut + + +;//////////////////// tuen off axus.L.eoffset-enable +;vvv +M198 ; will be replaced by a trap at end of state machibne +;^^^ + +; SEDM comp should have hit last state of state machinbe +; and be stuck in a loop +; becuz SEDM.enable == Falsee +; LATERvvv M197 will break that loop +; by setting SEDM.enable True +; +;////// goto 2nd posn +G0X1 +G0X2Y0 +G0Z0 + +;vvv +M197 ; set EDM.restart True AFTER in posn BEFORE M1nn codes w data +;^^^ + +;vvv DO 2nd cut +M199; done 1st M199 ; at top so SEDM creatd and enable early +;^^^ +; 26.10.2025 try deep cut using non-updown methoc +M162 P-2.304 Q.255 ; expect DRO +M163 P0 Q00.10 +M160 P34 +M161 P25 Q25 +M166 P0 ; no jump +M165 P1 ; pitch + +M00 ; nrcc?? yes , alloes EDM cut +;vvv +M198 ; will be replaced by a trap at end of state machibne +;^^^ + +M197 + +; SEDM.restart should be FALSE ( if 2nd pass thru SM happened) + +G0Z1 ; move tp a 3rf posn +G0X3Y0 +; +G0Z2 ; vizual somethong after 2nd cut did 2nd cut iccur> + +;//////////////////////////////// +M02 +% + +; vvv for ref +;M66 E0 L0; queue buster diff --git a/configs/sim/axis/sedm/ngc/SEDMmult07.ngc b/configs/sim/axis/sedm/ngc/SEDMmult07.ngc new file mode 100644 index 00000000000..25f4e3e9034 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmult07.ngc @@ -0,0 +1,136 @@ +;SEDMmult07.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-2.304 Q.255 ; expect DRO + M163 P0 Q00.10 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 100 (limit) + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + G0Z3 + G0X1Y0 + G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + G0Z1 + G0X2Y0 + G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + G0Z1 + G0X3Y0 + G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + G0Z1 + G0X4Y0 + G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + G0Z1 + G0X4Y1 + G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + G0Z1 + G0X3Y1 + G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + G0Z1 + G0X2Y1 + G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + G0Z1 + G0X1Y1 + G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;************************* + ;//////////////////// Posn 1 + G0Z1 + G0X1Y2 + G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + G0Z1 + G0X2Y2 + G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + G0Z1 + G0X3Y2 + G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + G0Z1 + G0X4Y2 + G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + G0Z1 + G0X4Y3 + G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + G0Z1 + G0X3Y3 + G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + G0Z1 + G0X2Y3 + G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + G0Z1 + G0X1Y3 + G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z3 +G0X0Y0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMmultDStraight01.ngc b/configs/sim/axis/sedm/ngc/SEDMmultDStraight01.ngc new file mode 100644 index 00000000000..56ccda221b3 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmultDStraight01.ngc @@ -0,0 +1,210 @@ +;SEDMmult07.ngc +; hard to press PEEK bntn cuz yimw winoiw when bvtn enabled is small, so make it deeper DUH +; +; YAY DRO is relative to THID cut, and is Rel to MC0,0,0, when m,ovinge to nrxt cut +; one shift is wrong, bad copy and paste out of sync +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-5.304 Q.255 ; wasa -2.304 expect DRO + ; vvv straight cut (no wigl) + M163 P0 Q0.0 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 100 (limit) + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + + ; remove G54 offsets ( G34 id aligned w L1 in G10L2Pi....msr from 'here' + g10l2p1x0y0z0; remove shift + + G0Z3; keep constant ht in wk area + # ^^^ motion msrd from ??? G53 ??? + + g10l2p1x1y0z0; add shift, mder from HERE + + g0x0y0z1; x at Rplane above shifted posn ??? above + ;G0X1Y0 + ;G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y0z0 + g0x0y0z1 + ;G0Z1 + ;G0X2Y0 + ;G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x3y0z0 + g0x0y0z1 + ;G0Z1 + ;G0X3Y0 + ;G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y0z0 + g0x0y0z1 + ;G0Z1 + ;G0X4Y0 + ;G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y1z0 + g0x0y0z1 + ;G0Z1 + ;G0X4Y1 + ;G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + g10l2p1x3y1z0 + G0Z3; keep constant ht in wk area g10l2p1x3y1z0 + g0x0y0z1 + ;G0Z1 + ;G0X3Y1 + ;G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x1y3z0 + g0x0y0z1 + ;G0Z1 + ;G0X2Y1 + ;G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y1z0 + g0x0y0z1 + ;G0Z1 + ;G0X1Y1 + ;G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;************************* + ;//////////////////// Posn 1 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x1y1z0 + g0x0y0z1 + ;G0Z1 + ;G0X1Y2 + ;G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x1y2z0 + g0x0y0z1 + ;G0Z1 + ;G0X2Y2 + ;G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y2z0 + g0x0y0z1 + ;G0Z1 + ;G0X3Y2 + ;G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x3y2z0 + g0x0y0z1 + ;G0Z1 + ;G0X4Y2 + ;G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y2z0 + g0x0y0z1 + ;G0Z1 + ;G0X4Y3 + ;G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y3z0 + g0x0y0z1 + ;G0Z1 + ;G0X3Y3 + ;G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x3y3z0 + g0x0y0z1 + ;G0Z1 + ;G0X2Y3 + ;G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y3z0 + g0x0y0z1 + ;G0Z1 + ;G0X1Y3 + ;G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10l2p1x0y0z0 + +G0Z3 +G0X0Y0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMmultDStraight02.ngc b/configs/sim/axis/sedm/ngc/SEDMmultDStraight02.ngc new file mode 100644 index 00000000000..7fedcec6b43 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmultDStraight02.ngc @@ -0,0 +1,212 @@ +;SEDMmult07.ngc +; hard to press PEEK bntn cuz yimw winoiw when bvtn enabled is small, so make it deeper DUH +; +; YAY DRO is relative to THID cut, and is Rel to MC0,0,0, when m,ovinge to nrxt cut +; one shift is wrong, bad copy and paste out of sync +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-5.304 Q1.0 ; 22.11.2025 now Q is RPlane wasa -2.304 expect DRO + ; vvv straight cut (no wigl) + M163 P0 Q0.0 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 100 (limit) + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + + ; remove G54 offsets ( G34 id aligned w L1 in G10L2Pi....msr from 'here' + g10l2p1x0y0z0; remove shift + G53G0Z3; keep constant ht in wk area + ; ^^^ motion msrd from ??? G53 ??? + g10l2p1x1y0z2; add shift, mder from HERE + ; NB ^^^ does not have motion, its just what msrmenst refer to ( the ref pt) + + ; TODO need to yt *move with sensing on) + ; move to Rplabe ( rel to new ref pt) + ; should NOT be included in FullDepth + ; vvv move 1 mmm above ref pt + g0x0y0z1; x at Rplane above shifted posn ??? above + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1x0y0z0 + G53G0Z3; keep constant ht in wk area + g10l2p1x2y0z1 + g0x0y0z1 + ;G0Z1 + ;G0X2Y0 + ;G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + g10l2p1x0y0z0 + G53G0Z3; keep constant ht in wk area + g10l2p1x3y0z0 + g0x0y0z1 + ;G0Z1 + ;G0X3Y0 + ;G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + g10l2p1x0y0z0 + G53G0Z3; keep constant ht in wk area + g10l2p1x4y0z-1 + g0x0y0z1 + ;G0Z1 + ;G0X4Y0 + ;G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y1z0 + g0x0y0z1 + ;G0Z1 + ;G0X4Y1 + ;G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + g10l2p1x3y1z0 + G0Z3; keep constant ht in wk area g10l2p1x3y1z0 + g0x0y0z1 + ;G0Z1 + ;G0X3Y1 + ;G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x1y3z0 + g0x0y0z1 + ;G0Z1 + ;G0X2Y1 + ;G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y1z0 + g0x0y0z1 + ;G0Z1 + ;G0X1Y1 + ;G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;************************* + ;//////////////////// Posn 1 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x1y1z0 + g0x0y0z1 + ;G0Z1 + ;G0X1Y2 + ;G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x1y2z0 + g0x0y0z1 + ;G0Z1 + ;G0X2Y2 + ;G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y2z0 + g0x0y0z1 + ;G0Z1 + ;G0X3Y2 + ;G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x3y2z0 + g0x0y0z1 + ;G0Z1 + ;G0X4Y2 + ;G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y2z0 + g0x0y0z1 + ;G0Z1 + ;G0X4Y3 + ;G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x4y3z0 + g0x0y0z1 + ;G0Z1 + ;G0X3Y3 + ;G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x3y3z0 + g0x0y0z1 + ;G0Z1 + ;G0X2Y3 + ;G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + g10l2p1x0y0z0 + G0Z3; keep constant ht in wk area + g10l2p1x2y3z0 + g0x0y0z1 + ;G0Z1 + ;G0X1Y3 + ;G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10l2p1x0y0z0 + +G0Z3 +G0X0Y0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMmultDStraight3-NoWuglandLASTorb.ngc b/configs/sim/axis/sedm/ngc/SEDMmultDStraight3-NoWuglandLASTorb.ngc new file mode 100644 index 00000000000..180e7cb3899 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmultDStraight3-NoWuglandLASTorb.ngc @@ -0,0 +1,95 @@ +;SEDMmulDstraight3.ngc +; +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.0 ; FD RPlabe + M163 P0 Q0.0; OrbType Circle, EiglRad 50um + M160 P34 Q0.254 ; etabnum, MsrdUNS + M161 P15 Q15 + M166 P0 ; no jump + M165 P1; Pitch == 1 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1 X0 Y0 Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro +G0 Z3 ; CPlane + +o110 while [#1 LT #2] + + ;//////////////////// Posn 1 + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z#4 ;RPlane rel to DATUM + + ;//////////////////// Cut 1 code + o200 call + ;g1z-2 + ;g1z#4 + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3 ;CPlane abso mc coords + + ;-------------------------- + g10l2p1 x12 y0 z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call + ;g1z-2 + ;g1z#4 + ;//////////////////// + g10l2p1 x0 y0 z0 ; UNSHIFT + G0Z#3 + + ;----------------------------- + g10l2p1 x14 y0 z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#4 + + ;//////////////////// + o200 call + ;g1z-2 + ;g1z#4 + ;//////////////////// + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3 + + ;--------------------------------- + g10l2p1 x16 y0 z-1 ; set DATUM 4 + g0x0y0 + z#4 + + ;//////////////////// + o200 call + ;g1z-2 + ;g1z#4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + + G10L2P1 X0 Y0 Z0 + G0Z#3 + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1 X0 Y0 Z0 ; unshift +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M02 +% + goz-2 diff --git a/configs/sim/axis/sedm/ngc/SEDMmultDStraight3-Wugland1stOrb.ngc b/configs/sim/axis/sedm/ngc/SEDMmultDStraight3-Wugland1stOrb.ngc new file mode 100644 index 00000000000..751f005f394 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmultDStraight3-Wugland1stOrb.ngc @@ -0,0 +1,89 @@ +;SEDMmulDstraight3.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + + M162 P-1.254 Q1.0 ; FD RPlane + + M163 P0 Q0.005; OrbType Circle, WiglRad 5um + + M160 P34 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q24 + ;P15 Q15; BegNR EndNR + + M166 P0 ; no jump + + M165 P1; Pitch == 1 + + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + g10l2p1 x0 y0 z0; UNSHIFT + G0Z3; CPlane + + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z1;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z3;CPlane abso mc coords + + ;-------------------------- + g10l2p1x12y0z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1x14y0z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#1 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1x16y0z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMmultDStraight3.ngc b/configs/sim/axis/sedm/ngc/SEDMmultDStraight3.ngc new file mode 100644 index 00000000000..1405207431a --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmultDStraight3.ngc @@ -0,0 +1,89 @@ +;SEDMmulDstraight3.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + + M162 P-1.254 Q1.0 ; FD RPlabe + + M163 P0 Q0.05; OrbType Circle, EiglRad 50um + + M160 P34 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q25 + ;P15 Q15; BegNR EndNR + + M166 P0 ; no jump + + M165 P1; Pitch == 1 + + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + g10l2p1 x0 y0 z0; UNSHIFT + G53G0Z3; CPlane + + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z1;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z3;CPlane abso mc coords + + ;-------------------------- + g10l2p1x12y0z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1x14y0z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#1 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + + g10l2p1x16y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1x4y0z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMmultDStraight3justWuglPlunge.ngc b/configs/sim/axis/sedm/ngc/SEDMmultDStraight3justWuglPlunge.ngc new file mode 100644 index 00000000000..933e70ec01d --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmultDStraight3justWuglPlunge.ngc @@ -0,0 +1,91 @@ +;SEDMmulDstraight3.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + + M162 P-1.254 Q1.0 ; FD RPlabe + + M163 P0 Q0.05; OrbType Circle, EiglRad 50um + + M160 P34 Q0.254 ; etabnum, MsrdUNS + + M161 P25 Q25 + ;P15 Q15; BegNR EndNR + + M166 P0 ; no jump + + M165 P1; Pitch == 1 + + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +3.000 ; CPlane +#4 = +1.000 ; RPlane + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + g10l2p1 x0 y0 z0; UNSHIFT + G53G0Z3; CPlane + + g10l2p1 x10 y0 z2; DATUM for cut #1 + g0x0y0 + z1;RPlane rel to DATUM + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z3;CPlane abso mc coords + + ;-------------------------- + g10l2p1x12y0z1 ; DATUM 2 + g0x0y0 ; rapid to DATUM 2 ctr + z#4 ; rapid to RPlane + ;//////////////////// + o200 call ; cut Detail 2 + ;//////////////////// + + g10l2p1x0y0z0 ; UNSHIFT + G0Z#3 + + g10l2p1x14y0z0 ; Set DATUM 3 + g0x0y0 ; rapid to DATUM 3 ctr + z#1 + ;//////////////////// + o200 call ; cut dertail 3 + ;//////////////////// + + g10l2p1x0y0z0 ;UNSHIFT + G0Z#3 + + g10l2p1x16y0z-1 ; set DATUM 4 + g0x0y0 + z#4 + ;//////////////////// + o200 call ; cut detail 4 + ;>>>>>>>>>>>>>>>>>>>>>>>>> + + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 +G0Z3 +G0X0Y0 ; alreaady at Cplane, moce to convenient x y +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMmultStraight01.ngc b/configs/sim/axis/sedm/ngc/SEDMmultStraight01.ngc new file mode 100644 index 00000000000..c51acf77404 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMmultStraight01.ngc @@ -0,0 +1,137 @@ +;SEDMmult07.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-2.304 Q.255 ; expect DRO + ; vvv straight cut (no wigl) + M163 P0 Q0.0 + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 100 (limit) + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + G0Z3 + G0X1Y0 + G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + G0Z1 + G0X2Y0 + G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + G0Z1 + G0X3Y0 + G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + G0Z1 + G0X4Y0 + G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + G0Z1 + G0X4Y1 + G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + G0Z1 + G0X3Y1 + G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + G0Z1 + G0X2Y1 + G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + G0Z1 + G0X1Y1 + G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;************************* + ;//////////////////// Posn 1 + G0Z1 + G0X1Y2 + G0Z0 + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + G0Z1 + G0X2Y2 + G0Z0 + ;//////////////////// CUT 2 code + o200 call + ;//////////////////// posn 3 + G0Z1 + G0X3Y2 + G0Z0 + ;//////////////////// CUT 3 cmds + o200 call + ;//////////////////// posn 4 + G0Z1 + G0X4Y2 + G0Z0 + ;//////////////////// CUT 4 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + ;//////////////////// Posn 5 + G0Z1 + G0X4Y3 + G0Z0 + ;//////////////////// Cut 5 code + o200 call + ;//////////////////// posn 6 + G0Z1 + G0X3Y3 + G0Z0 + ;//////////////////// CUT 6 code + o200 call + ;//////////////////// posn 7 + G0Z1 + G0X2Y3 + G0Z0 + ;//////////////////// CUT 7 cmds + o200 call + ;//////////////////// posn 8 + G0Z1 + G0X1Y3 + G0Z0 + ;//////////////////// CUT 8 ccmds + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z3 +G0X0Y0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMsingle01.ngc b/configs/sim/axis/sedm/ngc/SEDMsingle01.ngc new file mode 100644 index 00000000000..f34bf897c6b --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMsingle01.ngc @@ -0,0 +1,50 @@ +;SEDMsingl101.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-2.304 Q.255; RifPt at -2.049 ?? NO at -1.049 + ; so i hace depth rel to startposn + ; I'd like septh to be absolut ( butt reduce by UNS... + ; DOH i have nbo Datum Sjift l;ike Herif + ; with Datum Shift, i cvould mopbve 1mm over shift pt + ; then cut rel to ahift pt + ;??? how to set G5x from ttable?? + ; + M163 P0 Q0.0;starghtr plunge + M160 P34 + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) + +o110 while [#1 LT #2] + ;//////////////////// Posn 1 + G0Z3 + G0X1Y0 + ;G0Z1; cut to -1.049 + G0Z-1; cit to -3.049 + ;//////////////////// Cut 1 code + o200 call + ;>>>>>>>>>>>>>>>>>>>>>>>>> + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G0Z3 +G0X0Y0 +;////////// end pgm +M02 +% diff --git a/configs/sim/axis/sedm/ngc/SEDMstraight01.ngc b/configs/sim/axis/sedm/ngc/SEDMstraight01.ngc new file mode 100644 index 00000000000..29152a751cc --- /dev/null +++ b/configs/sim/axis/sedm/ngc/SEDMstraight01.ngc @@ -0,0 +1,30 @@ +;SEDMstraight01.ngc +; +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +;//////////////////// Posn 1 +G0Z3 +G0X1Y0 +G0Z0 + +M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH +M199 +M162 P-2.304 Q.255 ; expect DRO +M163 P0 Q0.0 +M160 P34 +M161 P25 Q25 +M166 P0 ; no jump +M165 P1 ; pitch +M00 +M198 + +;//////////////////// goto exit posn +G0Z3 +G0X0Y0 +M02 +% diff --git a/configs/sim/axis/sedm/ngc/XMPL.ngc b/configs/sim/axis/sedm/ngc/XMPL.ngc new file mode 100644 index 00000000000..fda502022ff --- /dev/null +++ b/configs/sim/axis/sedm/ngc/XMPL.ngc @@ -0,0 +1,58 @@ +;XMPLE.ngc cuts Z negative -1.204mm deerp +; DATUN for cut X1.0 Y 0 Z1.0 +; ORBIT type SQUARE +; ETABLE 34.ENC (This just finishing a cavity) +; ETABLE BegNR 17 EndNR 15 +; MsrdUNS == Etable UNS +o200 sub + M66 E0 L0 ;NEED QUEIE BUSTER so motion is stopped + M199 ; This begins EDM control + M162 P-1.304 Q+1.00 ; awt PrintDepth and Rplanemore tests per hr lookimg fdor bad tri from peri tto SPO + M163 P1 Q0 ; OrbType SQR, no 'Wigl' for bore + M160 P34 Q0.254 ; Etable, MsrdUNS + M161 P17 Q15 ; BeginningNR in Etable, EndNR + M00 ; needed for ExternalOffsets + M198 ; Rnd SEDM control + ; thsi last line wont be executed + ; untill AEDM comp finisshes +o200 endsub ; return to NGC code and LCNC position control +;now thw main NGC progtram poses the tool. and calls the o-sub. +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; posing can be rapid +G10L2P1 X0 Y0 Z0 ;'UNSHIFT' +; +#1 = 0 ;counter initial value +#2 = 1 ;counte max value +#3 = +2.000 ; Cplane above clamping/fixtires +#4 = +1.0 ; Rplane above woek wher EDM Power is turned on +; +o110 while [#1 LT #2] + g10l2p1 x0 y0 z0 ; UNSHIFT + G0Z5 ; manl tool chg for ToolAxis + ;//////////////////// DATUN for cut + g10l2p1 x1 y 0 z1 ;DATUM ref [posn + g0z#3 ;Cplane (2mm avove the 1mm DATUM) + g0 x0 y0 ;cavity center + z#4 ;RPlane rel to DATUM at G53 2.5 now + ;//////////////////// Cut + o200 call + ;//////////////////// + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3 ;Cplane rel toDATUM + ; + #1 = [#1 + 1] ;bump ctr, Useful for usinga Positionn list +o110 endwhile +;//////////////////// goto exit posn, adjust fdor G17.18/19 and CutDirection +G10L2P1X0Y0Z0 ;UNHIFT +G0Z5 ;manual Tool Chg height and tool axis +G0X0Y0 ;manual Tool Vhg posn for 'other' axis alreaady at Cplane, moce to convenient x y +;//////////////////// end pgm +M197 ;T turn off JumpENA if leaft on +M02 +% + diff --git a/configs/sim/axis/sedm/ngc/a.ngc b/configs/sim/axis/sedm/ngc/a.ngc new file mode 100644 index 00000000000..9773d5d3175 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/a.ngc @@ -0,0 +1,59 @@ +;SEDM0Asmall.ngc +; 1st 2 posmns of SEDM0A.ngc +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.085 + M163 P0 Q0.085 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +; ^^^ UNSHIFT +;g0x0y0z0; just get c on plot + +G0X-2Y2Z3; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +;g4p5 + +;//////////////////// Posn 1 + +G10L2P1X1Y0Z1 ; NEW DATUM + +G0X0Y0z1 ; move over new datum at CPlane + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +; this doesnt get exec'd if QUIT +; BUT +; pgm b3gina w same, so safe + +;G10L2P1x0y0z0 ; UNSHIFT + +;look whre tool is at +; IS at x1 y0 z0 no hairball +; should be at x1 y0 z1 + +;g4p5 +;g53g0x0y0z0; moves to x0y0z-2 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/axnrgwigl25-15.ngc b/configs/sim/axis/sedm/ngc/axnrgwigl25-15.ngc new file mode 100644 index 00000000000..8641957d938 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/axnrgwigl25-15.ngc @@ -0,0 +1,61 @@ +;axmgwigl25-15.ngc +; z neg bore with wig +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.1 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G19; toolaxis is X + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +; ^^^ UNSHIFT +;g0x0y0z0; just get c on plot + +G0X-2Y2Z3; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +;g4p5 + +;//////////////////// Posn 1 + +G10L2P1X1Y0Z1 ; NEW DATUM + +G0X0Y0z1 ; move over new datum at CPlane + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +; this doesnt get exec'd if QUIT +; BUT +; pgm b3gina w same, so safe + +;G10L2P1x0y0z0 ; UNSHIFT + +;look whre tool is at +; IS at x1 y0 z0 no hairball +; should be at x1 y0 z1 + +;g4p5 +;g53g0x0y0z0; moves to x0y0z-2 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/axposwigl25-15.ngc b/configs/sim/axis/sedm/ngc/axposwigl25-15.ngc new file mode 100644 index 00000000000..21449232859 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/axposwigl25-15.ngc @@ -0,0 +1,53 @@ +;axposigl25-15.ngc +; x pos bore with wig +; x pos bore with wig +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.254 Q-1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.005 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G19 + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +; ^^^ UNSHIFT +;g0x0y0z0; just get c on plot + +G0X-2Y2Z-3; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +;g4p5 + +;//////////////////// Posn 1 + +G10L2P1X1Y0Z-1 ; NEW DATUM + +G0X0Y0z-1 + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +;G10L2P1x0y0z0 ; UNSHIFT +;g4p5 +;g53g0x0y0z0; moves to x0y0z-2 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/aynrgwigl25-15.ngc b/configs/sim/axis/sedm/ngc/aynrgwigl25-15.ngc new file mode 100644 index 00000000000..f990b8ab604 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/aynrgwigl25-15.ngc @@ -0,0 +1,61 @@ +;aymgwigl25-24.ngc +; z neg bore with wig +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.005 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G18; toolaxis is Y + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +; ^^^ UNSHIFT +;g0x0y0z0; just get c on plot + +G0X-2Y2Z3; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +;g4p5 + +;//////////////////// Posn 1 + +G10L2P1X1Y0Z1 ; NEW DATUM + +G0X0Y0z1 ; move over new datum at CPlane + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +; this doesnt get exec'd if QUIT +; BUT +; pgm b3gina w same, so safe + +;G10L2P1x0y0z0 ; UNSHIFT + +;look whre tool is at +; IS at x1 y0 z0 no hairball +; should be at x1 y0 z1 + +;g4p5 +;g53g0x0y0z0; moves to x0y0z-2 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/ayposwigl25-15.ngc b/configs/sim/axis/sedm/ngc/ayposwigl25-15.ngc new file mode 100644 index 00000000000..9d863cdf4a2 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/ayposwigl25-15.ngc @@ -0,0 +1,53 @@ +;ayposigl25-15.ngc +; y pos bore with wig +; y pos bore with wig +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.254 Q-1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.005 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G18 + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +; ^^^ UNSHIFT +;g0x0y0z0; just get c on plot + +G0X-2Y2Z-3; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +;g4p5 + +;//////////////////// Posn 1 + +G10L2P1X1Y0Z-1 ; NEW DATUM + +G0X0Y0z-1 + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +;G10L2P1x0y0z0 ; UNSHIFT +;g4p5 +;g53g0x0y0z0; moves to x0y0z-2 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/aznrgwigl.ngc b/configs/sim/axis/sedm/ngc/aznrgwigl.ngc new file mode 100644 index 00000000000..5bab120548c --- /dev/null +++ b/configs/sim/axis/sedm/ngc/aznrgwigl.ngc @@ -0,0 +1,36 @@ +;azmgwigl.ngc +; x neg bore with wig +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-.354 Q1.000 ;fd -0.354 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.05 ; circ orb 5 wiglrad + M160 P34 Q.254 ; etab filename msrdUNS + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + ;g4p + M00 + M198 +o200 endsub + +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking +G10 l2 p1 x0 y0 z0 ; UNSHIFT simplify dro to G53 +G0 X-2 Y2 Z3 ; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +G10 L2 P1 X1 Y0 Z1 ; NEW DATUM +G0 X0 Y0 z1 ; move over new datum at CPlane + +o200 call + +G10 L2 P1 x0 y0 z0 ; UNSHIFT +G0 x0 y0 z3 ; abso mc coords +M02 +% diff --git a/configs/sim/axis/sedm/ngc/aznrgwigl25-15.ngc b/configs/sim/axis/sedm/ngc/aznrgwigl25-15.ngc new file mode 100644 index 00000000000..fa36db35480 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/aznrgwigl25-15.ngc @@ -0,0 +1,58 @@ +;azmgwigl25-24.ngc +; x neg bore with wig +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.005 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +; ^^^ UNSHIFT +;g0x0y0z0; just get c on plot + +G0X-2Y2Z3; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +;g4p5 + +;//////////////////// Posn 1 + +G10L2P1X1Y0Z1 ; NEW DATUM + +G0X0Y0z1 ; move over new datum at CPlane + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +; this doesnt get exec'd if QUIT +; BUT +; pgm b3gina w same, so safe + +;G10L2P1x0y0z0 ; UNSHIFT + +;look whre tool is at +; IS at x1 y0 z0 no hairball +; should be at x1 y0 z1 + +;g4p5 +;g53g0x0y0z0; moves to x0y0z-2 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/aznrgwigl25-24.ngc b/configs/sim/axis/sedm/ngc/aznrgwigl25-24.ngc new file mode 100644 index 00000000000..341ec92216d --- /dev/null +++ b/configs/sim/axis/sedm/ngc/aznrgwigl25-24.ngc @@ -0,0 +1,40 @@ +;azmgwigl25-24.ngc +; x neg bore with wig +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + + M162 P-1.254 Q1.000 ;fd -1.254 RPlane 1.000 + + M163 P0 Q0.005 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q24 + M166 P0 ; no jump + M165 P1 ; pitch + ;g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +G0X-2Y2Z3 ; CPlane +;//////////////////// Posn 1 +G10L2P1X1Y0Z1 ; NEW DATUM +G0X0Y0z1 ; move to RPlane over new datum +;//////////////////// Cut 1 code +o200 call +;//////////////////// +G10L2P1X0Y0Z0 +G0Z3 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/azposwigl.ngc b/configs/sim/axis/sedm/ngc/azposwigl.ngc new file mode 100644 index 00000000000..24d4db81430 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/azposwigl.ngc @@ -0,0 +1,53 @@ +;azposigl.ngc +; z pos bore with wig +; z pos bore with wig +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.254 Q-1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.005 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q25 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G17 + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +; ^^^ UNSHIFT +;g0x0y0z0; just get c on plot + +G0X-2Y2Z-3; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +;g4p5 + +;//////////////////// Posn 1 + +G10L2P1X1Y0Z-1 ; NEW DATUM + +G0X0Y0z-1 + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +;G10L2P1x0y0z0 ; UNSHIFT +;g4p5 +;g53g0x0y0z0; moves to x0y0z-2 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/azposwigl25-15.ngc b/configs/sim/axis/sedm/ngc/azposwigl25-15.ngc new file mode 100644 index 00000000000..6c6a1864302 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/azposwigl25-15.ngc @@ -0,0 +1,51 @@ +;azposigl25-15.ngc wigl and 1 orb +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.254 Q-1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.010 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G17 + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +; ^^^ UNSHIFT +;g0x0y0z0; just get c on plot + +G0X-2Y2Z-3; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +;g4p5 + +;//////////////////// Posn 1 + +G10L2P1X1Y0Z-1 ; NEW DATUM + +G0X0Y0z-1 + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +;G10L2P1x0y0z0 ; UNSHIFT +;g4p5 +;g53g0x0y0z0; moves to x0y0z-2 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/azposwigl25-24.ngc b/configs/sim/axis/sedm/ngc/azposwigl25-24.ngc new file mode 100644 index 00000000000..e8bf1bb78f9 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/azposwigl25-24.ngc @@ -0,0 +1,51 @@ +;azposigl25-24.ngc wigl and 1 orb +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P+1.254 Q-1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + M163 P0 Q0.010 + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q24 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 + +G17 + +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +; ^^^ UNSHIFT +;g0x0y0z0; just get c on plot + +G0X-2Y2Z-3; dro show -2 2 3 and NO hairball +; move someplace in G53 sys +;g4p5 + +;//////////////////// Posn 1 + +G10L2P1X1Y0Z-1 ; NEW DATUM + +G0X0Y0z-1 + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +;G10L2P1x0y0z0 ; UNSHIFT +;g4p5 +;g53g0x0y0z0; moves to x0y0z-2 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/b.ngc b/configs/sim/axis/sedm/ngc/b.ngc new file mode 100644 index 00000000000..68456f3aea8 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/b.ngc @@ -0,0 +1,49 @@ +;b.ngc test orbits +;06.12.2025 never got to NR24 +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q-1.000 ;fd -1.254 RPlane 1.000 + ; vvv otbtype is circ (notused tho) no wigl + ;M163 P0 Q0.005; wigl should be smaller than 1st orbRAD + M163 P1 Q0.01; orbtype wiglrad + M160 P34 Q.254; etab filename msrdUNS + M161 P25 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G18 ; NECC TO BE AWARE OFTOOL AXIS +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 + +;//////////////////// Posn 1 + +G10L2P1X5Y-1Z5 ; NEW DATUM + +G0Y-1; move to RPlane 1mm furtgher than the 1mm of datum +G0X0Z0 ; move to ctr + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +; this doesnt get exec'd if QUIT +; BUT +; pgm b3gina w same, so safe + +G10L2P1x0y0z0 ; UNSHIFT + +G0X5Y-2Z5 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/bzn.ngc b/configs/sim/axis/sedm/ngc/bzn.ngc new file mode 100644 index 00000000000..8e7888f9eeb --- /dev/null +++ b/configs/sim/axis/sedm/ngc/bzn.ngc @@ -0,0 +1,68 @@ +;bzn.ngc cut x negative +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P-1.254 Q1.000 ;fd -1.254 RPlane 1.000 + M163 P0 Q0.01; orbtype wiglrad + M160 P34 Q.254; etab filename msrdUNS + M161 P15 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G17 ; NECC TO BE AWARE OFTOOL AXIS +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + + + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 +G0Z3; acts like g53 due to prev cmd Cplane in abso/mc coords +; !!! w cold boot i see x0 y0 z3 + +g4p5 +; then i se -5 -5 3 +M66 E0 L0 ; qbrkr +G10L2P1X5Y5Z0 ; NEW DATUM msrf from work surface ( wk at x0) +g4p5 +; then i see morion ro 0 0 3 + +M66 E0 L0 ; qbrkr +g4p5; should see x-5 y-5 z3 +G0X0Y0 ; move to ctr x0 y0 z3 +M66 E0 L0 ; qbrkr + +; tool goes to z+1 rel +; then to x-1rel for lommg tome 10sec g4p10 + +g0z1; see x0 y0 z1 +g4p10 + +; this is datum.ref pt +; cut should cut 1,000 -(-1.254 ) +; which mioves from +1 to -1 on rel dro (hairball) + +;//////////////////// Cut 1 code +o200 call; motion is rel to datum set prior +;see tool move to z-1 and orb appear +; then too rtn to ctr then up to SPO +; which is x0 y0 z1 +;//////////////////// + +G10L2P1x0y0z0 ; UNSHIFT +; should see dro chg to s5 y5 z??? + +; g53 unnecc G53G0Z3;CPlane abdo/mc coords +G0Z3;CPlane abdo/mc coords +G0X0Y0 +; should see x0 y0 z3 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/bzp.ngc b/configs/sim/axis/sedm/ngc/bzp.ngc new file mode 100644 index 00000000000..a20df547512 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/bzp.ngc @@ -0,0 +1,55 @@ +;bzp.ngc cut z pos +; +#11 = -3.00 ; CP;lane in G53 abso m.c coords +#12 = -1.0 ;RPlane rel to Datum + +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + M162 P1.254 Q-1.000 ;fd -1.254 RPlane 1.000 + M163 P1 Q0.01; orbtype wiglrad + M160 P34 Q.254; etab filename msrdUNS + M161 P15 Q15 + M166 P0 ; no jump + M165 P1 ; pitch + g4p2 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G17 ; NECC TO BE AWARE OFTOOL AXIS +G90 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +g10l2p1x0y0z0; UNSHIFT simplify dro to G53 + +;//////////////////// Posn 1 + +G53G0Z#11; Cplane in abso/mc coords + +G10L2P1X5Y5Z-2 ; NEW DATUM toolaxis at work surface in abso/mc coords + +g0z#12;RPlane rel to Datum +G0X0Y0 ; move to ctr + +; RPlane handl;ed by comp + +;//////////////////// Cut 1 code +o200 call + +;//////////////////// +; this doesnt get exec'd if QUIT +; BUT +; pgm b3gina w same, so safe + +G10L2P1x0y0z0 ; UNSHIFT + +G53G0Z#11 ;CPlane abdo/mc coords +G0X0Y0 + +M02 +% diff --git a/configs/sim/axis/sedm/ngc/circ-allNR/ZnegWigl88888819-all-circ.ngc b/configs/sim/axis/sedm/ngc/circ-allNR/ZnegWigl88888819-all-circ.ngc new file mode 100644 index 00000000000..503221ad527 --- /dev/null +++ b/configs/sim/axis/sedm/ngc/circ-allNR/ZnegWigl88888819-all-circ.ngc @@ -0,0 +1,67 @@ +;ZnwgWigl88888819-all-circ.ngc +;22.02.2026 i just hanad edited 99999919 +; hwci lookls ;like a CU/ST etab +; +o200 sub + M66 E0 L0 ;NEED QBUSTER AND sleep(0.010) in rComp BOTH + M199 + + ; vvv i dont like Rplane being a #var AND psassed to SEDM + ; but BASH cant hanfl r #vcars ( or $vars can work w bash, as you wisj) + M162 P-0.304 Q0.5 ; more tests per hr lookimg fdor bad tri from peri tto SPO + + M163 P1 Q0.05; OrbType SQR, no Wigl for more tests per hr + M160 P19 Q0.500 ; etabnum, MsrdUNS + ;M161 P25 Q10 + M161 P12 Q10 + M00 + M198 +o200 endsub + +;///////////////////// PREAMBLE +G21 ; mm +G90 +G17 +G61 ; exact path mode +G64 P0 ; set blend toleranve to 0 +F5000 ; wishful thinnking + +G10L2P1X0Y0Z0 ; UNSHIFT, cut posns will be G43 msr and rel dro + +G0Z3 +X0Y0 + +#1 = 0 (assign parameter #1 the value of 0) +#2 = 1 (limit) +#3 = +1.000 ; CPlane small for more test s per hr +#4 = +0.5 ; RPlane small for more test s per hr + +o110 while [#1 LT #2] + + g10l2p1 x0 y0 z0; UNSHIFT + G0Z#3; CPlane + + ;//////////////////// Posn 1 + g10l2p1 x0 y0 z0; DATUM for cut #1 (same as UNshift i dopmnt ;like ) + g0x0y0 + z#4;RPlane rel to DATUM + + ;//////////////////// Cut 1 code + o200 call + ;//////////////////// posn 2 + g10l2p1 x0 y0 z0 ;UNSHIFT + G0Z#3;CPlane abso mc coords + ; + #1 = [#1 + 1] +o110 endwhile + +;//////////////////// goto exit posn +G10L2P1X0Y0Z0 + +G0Z3 +X0Y0 + +;////////// end pgm +M197 ( turn off JumpENA if leaft on ) +M02 +% diff --git a/lib/python/SEDMhdrs.py b/lib/python/SEDMhdrs.py new file mode 100644 index 00000000000..0163a77bc93 --- /dev/null +++ b/lib/python/SEDMhdrs.py @@ -0,0 +1,155 @@ +#!/usr/bin/env python3 +# +# SEDMhdrs.py +# resides in /usr/lib/python3.11 +# or ~/yourRIP/lib/python +# +#06.02.2026 add new JumpLtype(s) +# is infor for mkJumpL where to get dat +# some rqrs build fromBreakPy +# some will use sections of know lumpLine +# +# contains variables commom to other +# can be imported by: +# feom SEDMhdrs import * +# +# 09082025 assing backup limit +""" +#shows a way to get ~header files +# in python3 +# +# 18072025 +# python has no 'header' files +# and has 'import' not @inmcliude" +# so +# i have some 'token's whcih are know to funcs +# and the funs are indiv .py files +# so +# from SEDMhdrs import * +# result: +# YAY all variables ~conmstants are available +# even tab completed +# +# BEWARE all ~consnta can be edited in a single file +# BUT +# if name.value is chgd, +# then chgs are needed +# in all files that used it +# +""" + +# JumpLtype +JumpBoreType = 1 # use part of sexisyting BoreL +#JumpStairsLeadIn dont jump on StairsLeadin too small +JumpStairsType = 2 # create a leg shape beg at BP end at BP +JumpOrbLeadInType = 3 #use section of existing Legshape +# in Heidenhain, i didnt jump if too far away... how did i tell? +JumpOrbPathType = 4 #create dwtour wqith legshape +#JumpOrbPathDetour = 5 #NO dont jump , thertes only 1 posn where there may be stock, else its just backaway to clear low V +NoJump = 10 # avoid 0 for unitialized cars + + +# beg--------- CINSTANTS -------- +FWD = +1 +# vvv 'HOLD' ??? what name to use.. pick one damnit +HOLD = 0 +BWD = -1 +# 18.11.2025 vvv new when already doFail, this is rtnd +DEAD = 666 + +ContBWDmax = 20 # maxximum continouous low voltage sample, causes ABORT + + +LEADIN = 1 +PERIPHERY = 2 +LEADOUT = 3 + +ESCAPE_END_AT_MIN = 1 # token means +ESCAPE_END_AT_MAX = 2 # token meaning +ESCAPE_DO_MORE_FWD = 3 # token meaning last move was FWD ( away from periphery ) and not near ends of escapepath, caller should process more points +ESCAPE_DO_MORE_WAIT = 4 # token meaning last move was WAIT ( no motion ) and not near ends of escapepath, caller should process more points +ESCAPE_DO_MORE_BWD = 5 # token meaning last move was BWD ( towards periphery ) and not near ends of escapepath, caller should process more points + +NO_PLACE_TO_GO = 6 # at orb vctr and gv is ko FIX w x retreatr code TRBD + +BACK_ON_PERI_OK =7 # escLine finished ok + +BACK_AFTER_PERI_AND_OK = 8# escLine finished ok +# new 09042025 +BACK_AFTER_BORE_AND_OK = 9# escLine finished ok + +# neww 25072025 +MISMATH_DISPT_RUFPT = 10 +# use BO_PLACE_TO_GO FAIL_ON_PERI = 21 +OK_START_LEADOUT = 22 + +tooManyContinuousBWDs = 11 +EscOkBackOnPath = 12 +EscapeFailNeedAbort = 13 + +PathFinishedOK = 14 + +# 17.08.2025 GVMIN GVMAX set by NOT hdrs.py +#03072025 GVVMIN GVMAX now globals 'constyants" +#02.09.2025 i want to set GVMAX and GV>",ETABPATH) +# ^^^^^^^^ +# NameError: name 'ETABPATH' is not defined + +ETABPATH = "." + +# G20 is 0(INCH) G21 is 1(MM) +INCHUNIT = 0 +MMUNIT = 1 + +NEG = -1 +POS = +1 + +CIRCLE = 0 +SQUARE = 1 + +# WaitFullDepthMsrdUNS = 1 +WaitFullDepthRplaneDist = 1 +WaitOrbitTypeWiglRADf = 2 + +# WaitEttabNumber = 3 +WaitEttabNumberMsrdUNS = 3 + +WaitBegEndNR = 4 +WaitPitch = 5 +WaitJumpwANTED = 6 +WaitGenReady = 7 +WaitM199 = 8 + +WaitPlunge = 11 +WaitDoPlungeOrbit = 12 + +WaitAllNRsDone = 13 +WaitThisOrbitDone = 14 +WaitNewNR = 15 +CleanUpPutAway = 16 +# 12.11.2025 chgd name WaitRestart = 17 + +WaitNewCut = 20